Getting started handset features wall mounting, Base unit features – VTech VT9108 User Manual

Page 2

Advertising
background image

wallboard

wooden

stud

PULSE

TELEPHONE
WALL JACK

AC ELECTRICAL

OUTLET

TONE

PULSE

TONE

GETTING STARTED

HANDSET FEATURES

WALL MOUNTING

Setting Up Your

VT 9108/VT 9105

1. Choose an area near an electrical outlet

and a telephone wall jack.

2. Connect the telephone line cord. Insert

one end of the telephone line cord into
the jack at the rear of the base unit. Plug
the other end into a telephone wall jack.
Make sure the plugs snap securely into
place.

3. Plug the AC power adapter into an

electrical outlet and the DC connector to
the back of the base unit.

CAUTION:Use only the AC adapter

shipped with your VT 9108/VT
9105. This is a Class 2 AC
adapter, specifically designed for
use with the VT 9108/VT 9105.

NOTE:

Connect power to the base unit
before placing the handset in the
cradle.

4. Set the TONE/PULSE switch on the base

unit. If you have touch tone service on
your phone line, set the switch to TONE.
If you have rotary service, set the switch
to PULSE.

5. CHARGE THE HANDSET BATTERIES

BEFORE USE. The batteries recharge
automatically whenever the handset is
in the base unit cradle. The batteries
must be charged for 24 hours before
using your phone for the first time.

6. CHECK FOR A DIAL TONE. After the

batteries are charged, pick up the
handset and press the PHONE key. The
IN USE indicator should light up, and
you should hear a dial tone. If not, see
IN CASE OF DIFFICULTY.

CAUTION:
1. Never install telephone wiring during a

lightning storm.

2. Never install telephone jacks in wet

locations unless the jack is specifically
designed for wet locations.

3. Never touch uninsulated telephone wires

or terminals unless the telephone line
has been disconnected at the network
interface.

4. Use caution when installing or modifying

telephone lines.

1.Choose a spot near an electrical outlet

and a telephone jack.Your phone
requires a modular telephone jack and
a standard electrical outlet (120V AC).
The power cord is six feet long; make
sure there is an electrical outlet within
reach of the base. The outlet should not
be controlled by a wall switch. If the
switch is ever turned off, the phone will
not operate.

2.Position the wall mount adapter on the

base. Line up the tabs on the wall mount
adapter with the holes on the bottom of
the base. Snap the wall mount adapter
firmly in place.

3.Mount the base on the wall. Position

the base so the mounting studs will fit
into the holes on the bottom of the base.
Position the power cord to extend down
the wall the phone is to be mounted on.
Slide the base down on the mounting
studs until it locks into place.

MEM, Number Button (0-9).

PROG KEY
* Press PROG key to enter PROGRAM

mode. See Programming Speed Dial
Numbers
for more details.

REDIAL KEY
* When you hear the dial tone, pressing

the REDIAL key will dial out the last
number that was called on your phone.

* It can also be used to store the last

number dialed into the speed dial
memory. See Storing a Redial Number
into Speed Dial
for details.

TONE/ KEY
* In PULSE dialing mode, this key is used

to switch to Temporary TONE dialing
mode.

VOLUME SWITCH
* There are three volume setting: Low,
Medium and High.
BATTERY LOW WARNING BEEP
* Upon pressing PHONE, the Handset will

emit two beeps to indicate that the battery
pack needs to be recharged.

IN USE LED
* The IN USE LED lights when the phone

line is being used by the handset.

* It flashes in cadence with an incoming

ring.

* It flashes quickly during PROG mode.
PHONE KEY/ FLASH KEY
* Press the PHONE key to make a call.
* If you are currently on a call, pressing

PHONE flashes the line. This would be
used with a feature like call waiting to
answer your second call.

CHAN KEY
* Pressing the CHAN key when the

handset is in use will activate a channel
change to the next free channel.

* This is used if you are experiencing

noise or interference on the current
channel.

OFF KEY
* Press the OFF key to exit all modes of

operation.

MEM KEY
* Press the MEM key to enter MEMORY

mode.

* The sequence for dialing out a speed

dial number in memory is: PHONE,

4.Connect the telephone cord. The

telephone line cord has a snap-in plug
at each end. Insert one of the plugs into
the jack on the bottom of the base. Insert
the other end of the plug into the wall
jack.

5.Connect the power cord. Plug the DC

connector into the DC jack at the rear of
the base unit. Plug the AC power
adapter into an electrical outlet.

6.Set the dial mode switch on the base

unit. If you have touch tone service on

your phone line, set the switch to TONE.

If you have rotary service, set the switch

to PULSE.

4

5

7

CHARGING LED
* The CHARGE LED illuminates steadily when

the handset is in the base cradle to indicate
that the handset battery is being charged.

PAGE KEY
* Press the PAGE key to page the

handset.

* Press it a second time to cancel a

page.

* The base will ring the handset 4

times before ending the page
automatically.

* The handset can also cancel the

page by pressing the OFF key.

BASE UNIT FEATURES

TONE/PULSE SWITCH
* This switch will switch the phone between

TONE dialing and PULSE dialing.

REPLACEMENT BATTERY ORDER FORM

For VTECH 9108/9105 Cordless Telephone

Name:

Address:

City:

State:

Zip:

daytime phone Number: (

)

ORDER INFORMATION
For Model VT 9108/VT 9105

(QTY.) Batteries @$19.95 each............................$

$5.95 Shipping & Handling Per Battery Ordered....................................................$

METHOD OF PAYMENT: DO NOT SEND CASH

CHECK MONEY ORDER VISA

MASTERCARD AMERICAN EXPRESS

CREDIT CARD#

EXP. DATE

CARD HOLDERÕS SIGNATURE

PLACE ORDER FORM AND PAYMENT IN ENVELOPE AND SEND TO:

VTECH COMMUNICATIONS
8770 SW NIMBUS AVENUE

BEAVERTON, OREGON 97008-7195 USA

YOU MAY ALSO ORDER BY PHONE. CALL 1-800-595-9511

CUT

6

CHAN KEY

OFF KEY

PROG KEY

REDIAL KEY

MEM KEY

VOLUME SWITCH

PHONE KEY

IN USE / LOW BATT LED

TONE/ KEY

CUT

Advertising
This manual is related to the following products: