weber 89796 - Manual (Page 10)

10
WWW.WEBER.COM ®
CHECK FOR GAS LEAKS
After a period of nonuse, we recommend that you perform the following maintenance
procedures for your safety.
ƽ WARNING: Check the hose before each use of the grill for
nicks, cracking, abrasions or cuts. If the hose is found to be
damaged in any way, do not use the grill. Replace using only
Summit
®
authorized replacement hose. Contact the Summit
®
Built-In Customer Service at 1-800-446-1071.
• Inspect the burner for correct fl ame pattern. Clean if necessary, following the
procedures outlined in the “General Maintenance” section of this manual.
• Check all gas fi ttings for leaks.
ƽ DANGER
Do not use an open fl ame to check for gas leaks. Be sure
there are no sparks or open fl ames in the area while you
check for leaks. Sparks or open fl ames will result in a fi re or
explosion, which can cause serious bodily injury or death
and damage to property.
ƽ WARNING: You should check for gas leaks every time you
disconnect and reconnect a gas fi tting.
Note - All factory-made connections have been thoroughly checked for gas leaks. The
burners have been fl ame-tested. As a safety precaution however, you should recheck
all fi ttings for leaks before using your Weber Gas Barbecue. Shipping and handling
may loosen or damage a gas fi tting.
ƽ WARNING: Perform these leak checks even if your barbecue
was dealer or store assembled.
You will need: a soap and water solution, and a rag or brush to apply it.
Note - Since some leak test solutions, including soap and water, may be slightly cor-
rosive, all connections should be rinsed with water after checking for leaks.
Make sure side burner is OFF.
To perform leak checks: open cylinder valve by turning the cylinder valve hand-wheel
counterclockwise.
ƽ WARNING: Do not ignite burners when leak checking.
Check for leaks by wetting the connections with the soap and water solution and
watching for bubbles. If bubbles form or if a bubble grows, there is a leak.
Some LP tanks have differing top collar assembles. (The top collar is the metal
protective ring around the valve.) One series of tanks mount with the valve facing front
(a). The other tanks mount with the valve facing away from the fuel scale (b). See
Illustration.
The LP cylinder is installed inside the tank enclosure or tank cabinet, on the tank scale.
1)
Turn the LP cylinder so the opening of the valve is either to the front, side or rear
of the Weber
®
gas barbecue. Lift and hook the cylinder onto the fuel gauge.
2) Lift tank up into position on the tank scale.
3) Loosen the cylinder lock wing nut. Swing the cylinder lock down. Tighten the wing
nut.
To Connect the hose to the cylinder:
4)
Remove the plastic dust cover from the valve.
5) Screw the regulator coupling onto the tank valve, clockwise, or to the right. Hand-
tighten only.
Note: This connection tightens clockwise and will not allow gas to fl ow unless the
connection is tight. The connection requires tightening by hand only.
ƽ WARNING: Do not use a wrench to tighten the connection.
Using a wrench could damage the regulator coupling and
could cause a leak.
You will need: LP cylinder, a soap and water solution and a rag or brush to apply it.
6)
Mix soap and water.
7) Turn on the cylinder valve.
8) Check for leaks by wetting the fi tting with the soap and water solution and
watching for bubbles. If bubbles form, or if a bubble grows, there is a leak.
If there is a leak, turn off the gas and tighten the fi tting. Turn the gas back on and
recheck with the soap and water solution.
If leak does not stop do not use the barbecue. Contact the Customer Service
Representative in your area using the contact information on our web site. Log onto
www.weber.com
®
.
9) When leak checking is complete, turn gas supply off at the source and rinse
connections with water.
(a)
(b)
GAS INSTRUCTIONS