Wibur Curtis Company SD2 - Manual (Page 5)

5
Item N Item N Item N Item N Item Nº PPPPPart N art N art N art N art Nº Description Description Description Description Description
COVER, TANK W/NOTCHES
GASKET, TANK LID
PROBE, WATER LEVEL
ELBOW, OVERFLOW, PLASTIC
KIT, DUMP VALVE 120V 12W
HEATING ELEMENT 1.6KW 120VAC W/NUTS
SENSOR, TEMPERATURE TANK
SWTICH, #4680 VESSEL LIMIT
BUSHING, CONICAL .469 ID SILICONE
TEE, INLET PLASTIC GEN USE
TANK ASSY, 1600W-120VAC
HEATING TANK COMPLETE, 1600W-120V
COVER, TOP
CANISTER ASSY, SMALL
CANISTER ASSY, LARGE
ELBOW, CANISTER
FAN, EXTRACT 120V 29CFM 60Hz
SPOUT ASSY, HOT WATER
TUBE, EXTENSION RED 2.5” LG.
COVER, SWITCH PANEL
PANEL, SWITCH 4 BUTTONS 4 LEDS
STRIKE, MAGNET SCREW MOUNTED
SPACER BOARD .25 OD x .125L
STEAM TRAP
MIXING BOWL
PILLAR, LOCATION BLACK 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26 WC-WC-5851
WC-43062 *
WC-5502 *
WC-29047
WC-3734 *
WC- 904-04*
WC-1438-101 *
WC- 521 *
WC-2628
WC-29046
WC-54210
WC-62016
WC-58137
CA-1113-01 *
CA-1111-01 *
CA-1026-03
WC-37123
WC-29601
CA-1037-6R
WC-58172
WC- 727
CA-1049-102
WC-43048 *
CA-1005-03 *
CA-1009-03 *
CA-1024-05 * 27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51 CA-1006-03 *
CA-1128*
WC-58173
WC-39471
WC-38290
CA-1095
CA-1011-05
WC-66011 *
WC-38269
WC-58144
WC-58180
WC- 826L *
WC- 788 *
WC- 718-101
WC- 102 *
WC-58142
WC-58127
CA-1049
WC-3765L*
WC-3518 *
WC-3503 *
WC-5310 *
WC-1030 *
WC-37201*
CA-1036 CHAMBER, WHIPPER
NOZZLE, DISPENSE SD2
DOOR, FRONT WA
LABEL, CONTROL PANEL SD2
LABEL, DOOR CURTIS LOGO SD2
CONNECTOR, ORIFICE WATER
BULKHEAD, WATER FITTING
PLATE, WHIPPER CHAMBER
LABEL, SPLASH PANEL
SCREEN, DRIP TRAY
PAN, DRIP TRAY
VALVE, INLET 1.15 GPM
CONTROL POWER MODULE HYBRID
TRANSFORMER ASSY, 240/120VAC-12VAC 500mA
SWITCH, TOGGLE NON-LIT 25A 120/240VAC
COVER, DUMP VALVES
COVER, SIDE ACCESS
MAGNET, SNAP-IN
KIT, INLET VALVE REPAIR FOR USE ON WC-826L
LEG, GLIDE 3/8”-16 X 1/2”
LEG, SCREW BUMPER 3/8-16 STUD
TUBING, 5/16” ID x 1/8” W SILICONE
HOSE, EXTRACTOR FAN
KIT, GEAR MOTOR & GEAR SD2 ONLY
GEAR, PLASTIC
Item N Item N Item N Item N Item Nº PPPPPart N art N art N art N art Nº Description Description Description Description Description
Illustrated Parts List
* * * * * Suggested Parts to Stock
1. Loosen the small screw on the metal guard. Rotate it away from the adjustment screw (fig. 1.).
2. Carefully, turn flow adjustment screw clockwise all the way in (see figure 2.). Observe restrictor position . Do not overtighten.
3. Now turn the flow adjustment screw counter clockwise three [3] turns (or 1½ turns from the fully open position).
4. Replace the metal guard.
5. Install the valve on the tank, attaching wires and silicone tube. Press the valve fully into the fitting on the heating tank.
II. To adjust a valve currently on your unit or to test the operation of the new valve:
A. Turn on power to the unit. Turn on the water line and allow the tank to refill.
B. Place a container under the nozzle. Allow the unit to return to set temperature (Ready indicator will light).
C. Press the dispense button at the station that you are adjusting.
D. Measure the water volume.
E. Making adjustments of the restrictor with the valve mounted on the tank.
1. Turn the adjustment screw clockwise to decrease water flow.
2. Turn the adjustment screw counter clockwise to increase the water flow..
III. Close the access panel, return canisters to the unit turn the product delivery elbows downward and close the front door.