White Rodgers 1F80-224 - Manual (Page 5)

5
1
Step Press Button(s) Displayed (Factory Default) Press or to select: COMMENTS
HOLD
(0:00)
0 to 8 hrs (in
15 minute increments)
2
(FA)
SL
Select temporary Hold time
4
5
LOC
(OFF)
ON
0 HI
(0)
4 LO to
4 HI
(F) C
Returns to normal operation
6
7
Select compressor lockout OFF or ON
Select temperature display adjustment higher or lower
Select temperature display to F or C
RUN
PRGM
and RUN
HOLD *
HOLD *
3 d-L
(ON)
OFF Select display backlight OFF or ON HOLD *
HOLD *
HOLD *
Select FA or SL (Fast or Slow) heating cycle rate
Configuration Menu
* Press HOLD to advance to next item or TIME to move backwards to previous item
5 5 5 5 5 Select Temperature Display Adjustment 4 LO to 4 HI Select Temperature Display Adjustment 4 LO to 4 HI Select Temperature Display Adjustment 4 LO to 4 HI Select Temperature Display Adjustment 4 LO to 4 HI Select Temperature Display Adjustment 4 LO to 4 HI -
Allows you to adjust the room temperature display 4° higher
or lower. Your thermostat was accurately calibrated at the
factory but you have the option to change the display
temperature to match your previous thermostat.
6) 6) 6) 6) 6) Select F° or C° Readout Select F° or C° Readout Select F° or C° Readout Select F° or C° Readout Select F° or C° Readout - Changes the display readout to
Centigrade or Fahrenheit as required.
OPERATING FEATURES OPERATING FEATURES OPERATING FEATURES OPERATING FEATURES OPERATING FEATURES
Now that you are familiar with the thermostat buttons and
display, read the following information to learn about the many
features of the thermostat.
• SIMULTANEOUS HEATING/COOLING PROGRAM SIMULTANEOUS HEATING/COOLING PROGRAM SIMULTANEOUS HEATING/COOLING PROGRAM SIMULTANEOUS HEATING/COOLING PROGRAM SIMULTANEOUS HEATING/COOLING PROGRAM
STORAGE
STORAGE STORAGE STORAGE STORAGE — When programming, you can enter both
your heating and cooling programs at the same time. There
is no need to reprogram the thermostat at the beginning of
each season.
• TEMPERATURE OVERRIDE TEMPERATURE OVERRIDE TEMPERATURE OVERRIDE TEMPERATURE OVERRIDE TEMPERATURE OVERRIDE — Press or until the
display shows the temperature you want. The thermostat
will override current programming and keep the room
temperature at the selected temperature until the next
program period begins. Then the thermostat will automati-
cally revert to the program.
• HOLD TEMPERATURE HOLD TEMPERATURE HOLD TEMPERATURE HOLD TEMPERATURE HOLD TEMPERATURE — The thermostat can hold any
temperature within its range for an indefinite period without
reverting to the programmed temperature. Momentarily
press HOLD button. HOLD
HOLD HOLD HOLD HOLD will be displayed. Then choose
the desired temperature by pressing or . The
thermostat will hold the room temperature at the selected
setting until you press RUN button to start program opera-
tion again.
• CONFIGURATION MENU CONFIGURATION MENU CONFIGURATION MENU CONFIGURATION MENU CONFIGURATION MENU — Allows you to customize
certain thermostat options.
PROGRAMMING YOUR THERMOSTAT PROGRAMMING YOUR THERMOSTAT PROGRAMMING YOUR THERMOSTAT PROGRAMMING YOUR THERMOSTAT PROGRAMMING YOUR THERMOSTAT
This section will help you plan your thermostat’s program to
meet your needs. For maximum comfort and efficiency, keep
the following guidelines in mind when planning your program.
• When heating (cooling) your building, program the
temperatures to be cooler (warmer) when the building is
vacant or during periods of low activity.
• During early morning hours, the need for cooling is
usually minimal.
Planning Your Program Planning Your Program Planning Your Program Planning Your Program Planning Your Program
Look at the factory preprogrammed times and temperatures
shown in the sample schedule. If this program will suit your
needs, simply press the RUN button to begin running the factory
preset program.
If you want to change the preprogrammed times and tempera-
tures, follow these steps.
Determine the time periods and temperatures for your program.
You must program four time periods. However, you may use the
same heating and cooling temperatures for consecutive time
periods.
Use the following table to plan your program time periods and
the temperatures you want during each period. Fill in the
complete table to have a record of your programs.
Start
Time Temperature
1ST HEAT 6:00 AM 70˚F
2ND HEAT 8:00 AM 62˚F
3RD HEAT 5:00 PM 70˚F
4TH HEAT 10:00 PM 62˚F
1ST COOL 6:00 AM 78˚F
2ND COOL 8:00 AM 85˚F
3RD COOL 5:00 PM 78˚F
4TH COOL 10:00 PM 82˚F
SAMPLE
Heating/Cooling Schedule Plan (Factory Program)
Period
Start
Time Temperature
1ST HEAT
2ND HEAT
3RD HEAT
4TH HEAT
1ST COOL
2ND COOL
3RD COOL
4TH COOL
Heating/Cooling Schedule Plan
Period