Walter Drake SW8 - Manual (Page 22)

16 Clock and Timer Functions
Press the desired numeric buttons to enter a new ‘ON’
time. Enter the time in ‘HH:MM’ and in 24 hour format.
Press the
CLEAR
BEEP
button to remove the ‘On Time’ to use
the timer as a Sleep timer. For a Wake timer, program
an 'On Time' and remove the 'OFF' time.
To set the ‘OFF’ time, Press the
TIMER
CLOCK
button again to
display ‘OFF' time.
Press the desired numeric buttons to enter a new ‘OFF’
time. Enter the time in ‘HH:MM’ and in 24 hour format.
Press the
CLEAR
BEEP
button to remove the ‘OFF’ time, if
desired.
Press the
TIMER
CLOCK
button again to enter TIMER 2 'ON'
time.
Press the
TIMER
CLOCK
button again to enter TIMER 2 'OFF'
time.
Finally, press the
TIMER
CLOCK
button to save the settings and
switch the display to normal readout values.
1
) Example for Setting Timer ‘
1
’
With frequency displayed, suppose it is desired to set
Timer ‘1’ for a local ON Time: ‘16:59’
OFF Time: ‘18:01’
Action:
Press
F
and then hold
TIMER
CLOCK
.
AGC
TIMER
ON
+60
+40
+20
9
7
5
3
1
F
L
FM
Press the button sequence:
BCB
1
,
BW
6
,
SSB
5
,
LAMP
9
AGC
TIMER
ON
+60
+40
+20
9
7
5
3
1
F
L
FM
Press TIMER
CLOCK
Press the button sequence:
BCB
1
,
AGC
8
,
DEL
0
,
BCB
1
AGC
TIMER
OFF
+60
+40
+20
9
7
5
3
1
F
L
FM
Press
TIMER
CLOCK
AGC
TIMER
ON
+60
+40
+20
9
7
5
3
1
F
L
FM
If it is desired to set 'Timer 2', use the same procedure as
that for 'Timer 1', otherwise,
Press
TIMER
CLOCK
,
TIMER
CLOCK
to exit setting Timer operation and
return to normal frequency display.
ENABLING/DISABLING TIMER OPERATION
Press the
F
button followed by the
TIMER
CLOCK
button.
The ‘TIMER’ symbol will light in addition to either or
both the timer ‘1’ or timer ‘2’ indication. After two
seconds with no entry, the display reverts back to
frequency readout.
Timer ‘1’ can be disabled/enabled by pressing the
numeric digit
BCB
1
on the keypad while the timer
enable display is showing.
Timer ‘2’ can be disabled/enabled by pressing the
numeric digit
AIR
2
on the keypad while the timer
enable display is showing.
Timers '1' and '2' Enabled
AGC
TIMER
+60
+40
+20
9
7
5
3
1
F FM
Timer '1' Enabled; Timer '2' Disabled
AGC
TIMER
+60
+40
+20
9
7
5
3
1
F FM
If either one or both the timer ‘1’ or timer ‘2’ are
enabled, the TIMER symbol will continue to be
displayed after the receiver is turned off. Be certain to
leave the volume setting at the desired level. The
receiver will automatically turn on and off as pro-
grammed. If both timers are disabled ( ‘-’ '-' is dis-
played), the timer programming in either or both
timers is retained, but no TIMER action will take place
until one or both are enabled.
Prior to enabling either or both timers, consider one of
two possible cases for each timer:
eg.) - To Enable TIMER '1' —
1) '-' is displayed: Press the
BCB
1
button to
display '1'.
2) '1' is displayed: Press the
BCB
1
button twice to
again display '1'.
It is important to note that the timer is enabled only
when the timer is deliberately changed from a ‘-’ to ‘1’,
or ‘-’ to ‘2’.
Even if the ‘1’ or ‘2’ is already displayed, the timer is
not enabled unless the ‘-’ to ‘1’ or ‘2’ transition occurs.
Setting a ‘-’ for either timer DISABLES the respective
timer.