Wayne-Dalton 600 - Manual (Page 6)

Printed in U.S.A.
Item #333072 Revised 4/2008
Distributed By:
6 0 0
S E R I E S
ROLLING GRILLES
PART I – GENERAL
1.01 Work Included
A. The opening will be equipped withWayne-Dalton
600 Series rolling grilles.
1.02 Related Work
A. Opening preparation,miscellaneous or structural metal
work,access panels,finish or field painting,field
electrical wiring,wire,conduit,fuses,and disconnect
switches are in the Scope ofWork of other divisions
or trades.
1.03 Reference Standards
A. ANSI/DASMA203 –American National Standards
Institute Specifications for non-rated fire rolling doors
published by Door &Access Systems Manufacturers
Association International.
B. ASTM A123 – Zinc [hot-dipped galvanized] coat-
ings
on iron and steel products.
C. ASTM A229 – Steel wire,oil-tempered for
mechanical springs.
D. ASTM A-653-94 – Steel sheet,zinc-coated
[galvanized] by the hot-dipped process,
commercial quality.
1.04 Quality Assurance
A. Rolling grilles and all accessories and components
required for complete and secure installations shall be
manufactured as a system from one manufacturer.
1.05 Systems Description
A. Rolling Grille:Type:
Model 600
B. Mounting:[steel] [wood] [masonry] jambs
C. Operation:[manual push-up] [crank] [chain hoist]
[motor] [motor with chain hoist]
D. Material:[Galvanized steel] [aluminum] [stainless steel]
1.06 Submittals
A. Shop Drawings:Clearly indicate the following:
1. All details required for complete operation
and installation.
2. Hardware locations.
3. Type of metal and finish for door sections.
4. Finish for miscellaneous components and
accessories.
B. Product Data:Indicating manufacturer’s product
data,and installation instructions.
1.07 Delivery, Handling, Storage
A. Deliver products in manufacturer’s original containers,
dry,undamaged,seals and labels intact.
B. Store and protect products in accordance with
manufacturer’s recommendations.
1.08 Warranty
A. Standard manufacturer’s one year warranty against
defects in material and workmanship.
PART I I – PRODUCTS
2.01 Curtain
A. Curtains are to be fabricated of 5/16" galvanized
steel horizontal rods,continuous from jamb to jamb,
covered with aluminum tubes.Vertical links and tubes
available in stainless,aluminum or galvanized steel.End
links insure that grille cannot be pulled from guides.
2.02 Guides
A. Guides will be of extruded aluminum with wool pile
inserts to contact both faces of grille,acting as wearing
surfaces and sound deadener.
2.03 Brackets
A. Bracket Plates will be of 3/16” minimum [1/4”] steel
plate.Sealed ball bearings to support the
counterbalance assembly.Brackets to form end
closures and support hoods.
2.04 Counterbalance
A. Curtain to be coiled on a pipe of sufficient size to
carry door load with deflection not to exceed .033"
per foot of door span and to be correctly balanced by
helical springs,oil tempered torsion type.Cast iron
barrel plugs will be used to anchor springs to tension
shaft and pipe.
2.05 Hood
A. When required,hood is to be fabricated of 24-gauge
galvanized steel (stainless steel) (20 B&S gauge
aluminum).Provide intermediate hood supports over
16'0" opening width.
2.06 Finish
Finish for aluminum surfaces is to be (mill) (clear
anodized 204R1)(bronze anodized).Non-galvanized
steel surfaces are to be painted one shop coat of rust
inhibiting primer.Stainless steel to be #304 brushed.
2.07 Operation
A. Grilles will be operated by means of (manual,with lift
handles) (by chain and gear–maximum pull of 35 lbs.)
(by fully enclosed awning type crank gearing and
removable crank arm) (by motor operator).
2.08 Locking
A. Manual or crank operated grilles to be by means of
slide bolt locking device operable from inside or
outside.Chain lock keeper on chain operated doors.
Motor operated grilles to include self-locking gearing
plus chain locking device for emergency chain.
Note: When specifying locks on electric-motor operated
doors,electric interlocks should also be specified to
prevent operation when lock bolts are engaged in the
guides,thus preventing damage to the curtain
and/or operator.
PART III – EXECUTION
3.01 Installation
A. General:
1. Install grilles in accordance with manufacturer’s
instructions and standards.Installation shall be by an
authorizedWayne-Dalton representative.
2. Verify that existing conditions are ready to receive
rolling grille work.
3. Beginning of rolling grille work means acceptance
of existing conditions.
B. Install grille complete with necessary hardware,jamb
and head mold strips,anchors,inserts,hangers,and
equipment supports in accordance with final shop
drawings,manufacturer’s instructions,and as specified
herein.
C. Fit,align and adjust rolling grille assemblies level and
plumb for smooth operation.
D. Upon completion of final installation,lubricate,test and
adjust grilles to operate easily,free from warp,twist or
distortion and fitting for entire perimeter.
Note: Architect may consider providing a schedule when
more than one rolling grille or opening type is
required.
Because of continuing product improvements, we reserve the right to change the product specifications and designs without prior notice.
© 2008 Wayne-Dalton Corp. • One Door Drive • Mt. Hope, Ohio 44660 • 800-255-3046
Mt. Hope, OH • Dalton, OH • Trail, OH • Pensacola, FL • Portland, OR
For technical information, visit:
www. wayne-dalton .com/commercial
Note to specifiers: Words in brackets indicate frequently specified and highly recommended options.