Worksaver 300 - Manual (Page 6)

5 24
SAFETY INSTRUCTIONS
(continued)
Keep safety signs clean and legible at all times.
Replace safety signs that are missing or have become illegible.
Replaced parts that displayed a safety sign should also display the current sign.
Safety signs are available from your Distributor or Dealer Parts Department or the factory.
Be sure that the installation area is clean and dry. Be sure temperature is above 50ÞF (10ÞC).
Decide on the exact position before you remove the backing paper.
Remove the smallest portion of the split backing paper. Align the sign over the specified area and carefully
press the small portion with the exposed sticky backing in place.
Slowly peel back the remaining paper and carefully smooth the remaining portion of the sign in place. Small
air pockets can be pierced with a pin and smoothed out using the piece of sign backing paper.
How to Install Safety Signs:
SAFETY SIGNS
Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to pro-
vide safe equipment can be wiped out by a single careless act of an operator. It is the operator’s responsibili-
ty to read and understand ALL Safety and Operating instructions in the manual and to follow these. Accidents
can be avoided.
Know your controls and how to stop tractor, engine, and implement quickly in an emergency. Read this manu-
al and the one provided with your tractor.
In addition to the design and configuration of equipment, hazard control and accident prevention are depend-
ent upon the awareness, concern, prudence and proper training of personnel involved in the operation, trans-
port, maintenance and storage of equipment.
Train all new personnel and review instructions frequently with existing workers. A person who has not read
and understood all operating and safety instructions is not qualified to operate the machine. An untrained
operator exposes himself and bystanders to possible serious injury or death.
Working with unfamiliar equipment can lead to careless injuries. Read this manual, and the manual for your
tractor, before assembly or operating, to acquaint yourself with the machines. It is the implement owner’s
responsibility, if this machine is used by any person other than yourself, is loaned or rented, to make certain
that the operator, prior to operating:
1. Reads and understands the operator’s manuals.
2. Is instructed in safe and proper use.
SAFETY TRAINING
Do not allow children to operate this machine.
30” AUGER REPAIR PARTS
1 170562 6” Diameter Auger (30”) 1
170567 9” Diameter Auger (30”) 1
170572 12” Diameter Auger (30”) 1
2 210007 Auger Point – Screw Type 1
3 171903 Cutting Edge – 6” Augers Only 2
706021 Red Claw Digger Teeth – 9” & 12” Augers Var.
4 2503178 Bolt 3 /
8
” – 16NC x 1 1 /
4
” Carriage Head – 6” Augers 2
2503166 Bolt 1 /
2
” – 13NC x 1 1 /
4
” Carriage Head – 9” & 12” Augers Var.
5 2502014 Washer 3 /
8
” External Star – 6” Augers 2
2502003 Washer 1 /
2
” External Star – 9” & 12” Augers Var.
6 2500004 Nut 3 /
8
” – 16NC Full Hex – 6” Augers 2
2500003 Nut 1 /
2
” – 13NC Full Hex – 9” & 12” Augers Var.
7 2503012 Bolt 1 /
2
” – 13NC x 3” Hex Head 2
8 2502002 Washer 1 /
2
” Springlock 2
9 2500003 Nut 1 /
2
” – 13NC Full Hex 2
10 101131 Decal – Danger (Guard Missing) 1
NO.
REQ.
DESCRIPTION
PART
NO.
REF.
NO.