Dm2000vcm specifications – Yamaha DM 2000VCM User Manual
Page 11
D I G I T A L P R O D U C T I O N C O N S O L E D M 2 0 0 0
D I G I T A L P R O D U C T I O N C O N S O L E D M 2 0 0 0
DM2000VCM Specifications
General Specifications
Internal Signal Processing
32-bit (Accumulator 58-bit)
Sampling Frequency
Internal
44.1 kHz,48 kHz,88.2 kHz,96 kHz
External
Normal rate 44.1 kHz-10% to 48 kHz+6%
Double rate 88.2 kHz-10% to 96 kHz+6%
Signal Delay
Less than 2.3 ms CH INPUT to STEREO OUT
(@Sampling frequency = 48 kHz)
Less than 1.2 ms CH INPUT to STEREO OUT
(@Sampling frequency = 96 kHz)
Fader
motorized, touch sensitive: 100mm x 25
Total Harmonic Distortion
Less than 0.05% 20Hz to 20 kHz @+14dB into 600 ½
CH INPUT to STEREO OUT Less than 0.01% 1 kHz @+18dB into 600 ½
Input Gain = Min.
(@Sampling frequency = 48kHz)
Less than 0.05% 20Hz to 40 kHz @+14dB into 600 ½
Less than 0.01% 1 kHz @+18dB into 600 ½
(@Sampling frequency = 96kHz)
Frequency Response
0.5,-1.5dB 20Hz - 20 kHz @+4dB into 600 ½
CH INPUT to STEREO OUT (@Sampling frequency = 48 kHz)
0.5,-1.5dB 20Hz - 40 kHz @+4dB into 600 ½
(@Sampling frequency = 96 kHz)
Dynamic Range
110 dB typ.DA Converter (STEREO OUT)
(maximum level to noise level)
108 dB typ.AD+DA (to STEREO OUT) @ fs=48 kHz
106 dB typ.AD+DA (to STEREO OUT) @ fs=96 kHz
Hum & Noise*
-128dB Equivalent Input Noise.
(20Hz~20 kHz)
Rs =150W
-92dB residual output noise.STEREO OUT
Input Gain = Max.STEREO OUT off.
Input Pad = 0dB
Input Sensitivity = -60dB
-92dB (96dB S/N) STEREO OUT
STEREO fader at nominal level and
all CH INPUT faders at minimum level
-64dB (68dB S/N) STEREO OUTPUT
STEREO fader at nominal level and
one CH INPUT fader at nominal level
Maximum Voltage Gain
74dB CH INPUT (CH1-24) to STEREO OUT / OMNI (BUS) OUT
74dB CH INPUT (CH1-24) to OMNI (AUX) OUT (via pre input fader)
74dB CH INPUT (CH1-24) to CONTROL ROOM MONITOR OUT
(via STEREO bus)
* Hum & Noise are measured with a 6dB/octave filter @12.7 kHz;
equivalent to a 20 kHz filter with infinite dB/octave attenuation.
* Input Gain = Min.
* Total Harmonic Distortion is measured with a 6dB/octave filter @80kHz
Crosstalk (@1 kHz)
80dB adjacent input channels (CH1-24)
80dB input to output.
Power Requirements
U/C
120V
300W
60Hz
H
230V
300W
50Hz
B
230V
300W
50Hz
Dimensions
Height
257mm (including LCD)
Depth
821mm
Width
906mm
Net Weight
43kg
Operating free-air temperature range
10~35¡C
Storage temperature range
-20~60¡C
Libraries
Effect libraries (EFFECT1-8) Number of factory presets
67 (EFFECT3-8: 56)
Number of user libraries
61
Compressor libraries
Number of factory presets
36
Number of user libraries
92
Gate libraries
Number of factory presets
4
Number of user libraries
124
EQ libraries
Number of factory presets
40
Number of user libraries
160
Channel libraries
Number of factory presets
2
Number of user libraries
127
GEQ libraries (EQ1-6)
Number of factory presets
1
Number of user libraries
128
Surround Monitor libraries
Number of factory presets
1
Number of user libraries
32
Input patch libraries
Number of factory presets
1
Number of user libraries
32
Output patch libraries
Number of factory presets
1
Number of user libraries
32
Bus to stereo libraries
Number of factory presets
1
Number of user libraries
32
Analog Input Characteristics
Input Terminals
Connector in
Console
Actual Load
Impedance
For Use With
Nominal
Sensitivity
*
1
Nominal
Max. before
clip
0
-60dB
CH INPUT
A/B 1-24
26
3K ½
10K ½
600 ½ Lines
2TR IN ANALOG 2 [L,R]
-10dBV
(0.316 V)
-10dBV
(0.316 V)
+4dBV
(1.58V)
RCA Pin Jack
(Unbalanced)
*1.Sensitivity is the lowest level that will produce an output of +4dB (1.23V) or the nominal output level when the unit is
set to maximum gain.(all faders and level controls are maximum position.)
*2.XLR-3-31 type connectors are balanced. (1/Sleeve = GND, 2/Tip = HOT, 3/Ring = COLD)
*3.Phone jacks are balanced. (Tip = HOT, Ring = COLD, Sleeve = GND)
¥ In these specifications, when dB represents are specific voltage, 0dB is referenced to 0.775 Vrms.
¥ For 2TR IN ANALOG 2 levels, 0dBV is referenced to 1.00 Vrms.
¥ All 24 AD converters (CH1-24) are 24 bit linear,128times oversampling.
¥ +48V DC (phantom power) is supplied to CH INPUT (1-24) XLR type connectors via each individual switch.
50-600 ½ Mics
&
600 ½ Lines
-16dB
GAIN
Input Level
-70dB
(0.245mV)
-46dB
(3.88mV)
A:XLR-3-31 type
(Balanced) *
2
-60dB
(0.775mV)
-26dB
(38.8mV)
-2dB
(616mV)
B:Phone Jack
(TRS) (Balanced) *
3
-16dB
(0.123V)
0dB
(775mV)
+24dB
(12.28V)
+10dB
(2.45V)
INSERT IN 1-24
600 ½ Lines -6dB
(388mV)
+18dB
(6.16V)
Phone Jack
(TRS) (Balanced) *
3
+4dB
(1.23 V)
10K ½
10K ½
600 ½ Lines
2TR IN ANALOG 1 [L,R]
+4dB
(1.23V)
+18dB
(6.16V)
Phone Jack
(TRS) (Balanced) *
3
+4dB
(1.23 V)
Analog Output Characteristics
Output Terminals
Connector in Console
Actual Source
Impedance
For Use With
Nominal
Nominal
Max. before clip
STEREO OUT [L,R]
-10dBV (0.316V) +4dBV (1.58V) RCA Pin Jack
(Unbalanced)
+4dB (1.23V)
+18dB (6.16V) XLR-3-32 type
(Balanced) *
1
STUDIO
MONITOR OUT [L,R]
+4dB (1.23V)
+18dB (6.16V) Phone Jack
(TRS) (Balanced) *
2
C-R MONITOR OUT
LARGE [L,R]
+4dB (1.23V)
+18dB (6.16V) XLR-3-32 type
(Balanced) *
1
C-R MONITOR OUT
SMALL [L,R]
+4dB (1.23V)
+18dB (6.16V) XLR-3-32 type
(Balanced) *
1
OMNI OUT 1-8
+18dB
(default) +4dB (1.23V)
+18dB (6.16V) Phone Jack
(TRS) (Balanced) *
2
+4dB
-10dB (0.245V) +4dB (1.23V)
INSERT OUT 1-24
+4dB (1.23V)
+18dB (6.16V) Phone Jack
(TRS) (Balanced) *
2
PHONES
4mW
25mW
Stereo Phone Jack
(TRS) (Unbalanced) *
3
8 ½ Lines
40 ½ Lines
-
-
-
-
-
-
-
-
12mW
75mW
*1.XLR-3-32 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
*2.Phone jack are balanced. (Tip = HOT, Ring = COLD, Sleeve = GND)
*3.PHONES stereo phone jack is unbalanced.
(Tip = LEFT, Ring = RIGHT, Sleeve = GND)
¥ STEREO OUT [L,R] , 0dBV is referenced to 1.00 Vrms.
¥ In these specifications, when dB represents are specific voltage,
0dB is referenced to 0.775 Vrms.
¥ All output (except INSERT OUT 1-24) DA converters are 24 bit,
128times oversampling.
GAIN SW
Output Level
Digital Input Characteristics
*1.XLR-3-31 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
1
2
3
Terminal
2TR IN
DIGITAL
CASCADE IN
Format
AES/EBU
AES/EBU
IEC-60958
-
Data Length
24 bit
24 bit
24 bit
-
Level
RS422
RS422
0.5Vpp/75 ½
RS422
Connector in Console
XLR-3-31 type (Balanced) *
1
XLR-3-31 type (Balanced) *
1
RCA Pin Jack
D-SUB Half Pitch Connector 68P (Female)
Digital Output Characteristics
Available Mini-Ygdai Card Specifications
1
3
Terminal
2TR OUT
DIGITAL
CASCADE OUT
Format
-
Data Length
-
Level
RS422
RS422
RS422
Connector in Console
XLR-3-32 type (Balanced) *
4
XLR-3-32 type (Balanced) *
4
RCA Pin Jack
D-SUB Half Pitch Connector 68P (Female)
AES/EBU *
1
Professional
use
2
AES/EBU *
1
Professional
use
24 bit *
3
24 bit *
3
24 bit *
3
IEC-60958 *
2
Consumer
use
0.5Vpp/75 ½
*1.channel status of DIGITAL OUT 1, 2
type
: 2 audio channels
emphasis
: NO
sampling rate
: depends on the internal configuration
*2.channel status of DIGITAL OUT 3
type
: 2 audio channels
category code
: 2 channel PCM encoder/decoder
copy prohibit
: NO
emphasis
: NO
clock accuracy
: Level II (1000 ppm)
sampling rate
: depends on the internal configuration
*3.dither
: word length 16 - 24 bit
*4.XLR-3-32 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
600 ½ Lines
600 ½ Lines
10k ½ Lines
10k ½ Lines
10k ½ Lines
10k ½ Lines
600 ½ Lines
600 ½
150 ½
150 ½
150 ½
150 ½
150 ½
150 ½
100 ½
Yamaha
Maker
Model
Function
IN
OUT Format
Res / Freq
Connector
Note
Yamaha
MY8-AT
Digital I /O
8
8
ADAT
24 bit 44.1/48 kHz
Toslink x 2
Can handle 24 bit/96 kHz by double channel mode
MY8-AE
Digital I /O
8
8
AES/EBU 24 bit 44.1/48 kHz
D-sub 25pin
Can handle 24 bit/96 kHz by double channel mode
MY8-TD
Digital I /O
8
8
TDIF
24 bit 44.1/48 kHz
D-sub 25pin
Can handle 24 bit/96 kHz by double channel mode
MY16-AT
Digital I /O
16
16
ADAT
24 bit 44.1/48/88.2/96 kHz Toslink x 2
Can handle 24 bit/96 kHz by double channel mode
MY16-AE
Digital I /O
16
16
AES/EBU 24 bit 44.1/48/88.2/96 kHz D-sub 25pin
Can handle 24 bit/96 kHz by double channel mode
MY16-TD
Digital I /O
16
16
TDIF
24 bit 44.1/48/88.2/96 kHz D-sub 25pin
Can handle 24 bit/96 kHz by double channel mode
MY8-AD24
A to D In
8
-
8
-
24 bit 44.1/48 kHz
TRS x 8
Replacing MY8-AD (20 bit 44.1/48 kHz)
ÒeXi-ClockÓ Sync Capability
MY8-AEB
Digital I /O
(w/REF Video in)
8
AES/EBU
(AES-3id)
24 bit 44.1/48 kHz
BNC x 9
(In x 4, Out x4, REF Video in x 1)
MY4-DA
D to A Out
-
4
-
20 bit 44.1/48 kHz
XLR x 4
Check instructions for multiple use
MY16-mLAN mLAN Interface
16
16
IEEE 1394 24 bit 44.1/48kHz
1394 6pin
MY8-AD96
A to D In
8
-
-
24 bit 44.1/48/88.2/96 kHz D-sub 25pin
MY8-DA96
D to A Out
-
8
-
24 bit 44.1/48/88.2/96 kHz D-sub 25pin
MY8-AE96S Digital I /O
8
8
AES/EBU 24 bit 44.1/48/88.2/96 kHz D-sub 25pin
Sampling Rate Converter for Input, 3 cards max.with DM2000
MY8-ADDA96 Analog I /O
8
8
Analog
24 bit 44.1/48/88.2/96 kHz Euro Block
Refer to http://www.auvitran.com/
MY8-AE96
Digital I /O
8
8
AES/EBU 24 bit 44.1/48/88.2/96 kHz D-sub 25pin
Third Party
Maker
Model
Function
IN
OUT Format
Res / Freq
Connector
Note
AuviTran AVY16-ES
Digital I /O
16
16
Ether Sound 24 bit 44.1/48 kHz
RJ45 x 2, D-sub 9pin
Refer to http://www.aviom.com/
AVIOM
16/o-Y1
Digital I /O
-
16
A-net
24 bit 44.1/48 kHz
RJ45 x 1
Refer to http://www.audio-service.com/
Audio-Service MYMADI64
Digital I /O
64
64
MADI
24 bit 44.1/48/88.2/96 kHz
BNC x 2, Fiber optics
¥ Specifications and appearance subject to change without notice.
¥ All trademarks and registered trademarks are property of their respective owners.
Pro Tools
¨
is a trademark of Digidesign, Avid Technology Inc.
Nuendo
¨
is a trademark of Steinberg Media Technologies AG.
Adat is a trademark of Alesis Corporation.
Tascam, TDIF, MX2424 are trademarks of Teac Corporation.
HDR24/96 is a trademark of Mackie Designs Inc.
Cobranet and Peak Audio are trademarks of Cirrus Logic, Inc.
Macintosh is a trademark of Apple Computer Inc.
Windows is a trademark of Microsoft Corporation.
Go to www.yamahaproaudio.com to check “Guidance on the use of Mini-YGDAI cards”
Check instructions for multiple use
MY16-C
CobraNet Interface
16
16
CobraNet 20/24 bit 44.1/48/88.2/96 kHz RJ45 x 2
Check instructions for multiple use
MY16-CII
CobraNet Interface
16
16
CobraNet 20/24 bit 44.1/48/88.2/96 kHz RJ45 x 2
MY4-AD
A to D In
4
-
-
24 bit 44.1/48 kHz
XLR x 4