Entering manufacturer codes, English, Entering a code – Yamaha RX-V795aRDS User Manual
Page 73: Entering a code for a second (or third) vcr, Flashes twice, Press the mute key, Remote controller
71
English
Entering manufacturer codes
If you have a component which is not a Yamaha model, you can enter the code for the manufacturer of the component in the
corresponding position of the selector dial. By doing so, you can control the component with the remote controller.
Refer to the code list at the end of this manual for the code numbers you need.
Notes
●
Some Yamaha CD players and tape decks cannot be controlled with the default codes. To control such a model, enter the code
for the model in the corresponding position.
●
If there is no code applicable for your component in the code list, you must use the remote controller provided for the component.
1
Set the selector dial to the position for controlling the
component. (For example, set to “VCR” for a VCR.)
2
Press both of the VOLUME
and
keys at the
same time and hold them until the indicator flashes
twice.
3
Use the numeric keys to enter the four-digit
manufacturer code for the component to be used.
Make sure that the indicator flashes twice.
* If the indicator does not flash, repeat step 3 and enter
the code again.
4
Try operating the component with the remote controller
to check the code entering is successful.
Note
If the component cannot be controlled, enter another code for
the same manufacturer.
Entering a code
POWER
STANDBY
CD
TAPE/MD
MOVIE
THEATER 1
MOVIE
THEATER 2
/DTS
SURROUND
VCR
POWER
STANDBY
VCR
Flashes
twice.
Entering a code for a second (or third) VCR
You can use the CBL/DBS or DVD MENU position, or both of
them to control a second (and/or third) VCR if you do not use a
cable TV, DBS tuner, DVD player etc.
* If you will use the DVD MENU position for a second (or third)
VCR, you must enter the code for an LD player in the DVD/LD
position.
1
Set the selector dial to the CBL/DBS or DVD MENU
position.
2
Press both of the VOLUME
and
keys at the
same time and hold them until the indicator flashes
twice.
3
Press the MUTE key.
4
Use the numeric keys to enter the four-digit
manufacturer code for the second (or third) VCR. Make
sure that the indicator flashes twice.
* If the indicator does not flash, repeat step 4 and enter the
code again.
5
Try operating the component with the remote controller
to check the code entering is successful.
Note
If the component cannot be controlled, enter another code for
the same manufacturer.
POWER
STANDBY
CD
TAPE/MD
MOVIE
THEATER 1
MOVIE
THEATER 2
/DTS
SURROUND
DVDMENU
TV
VOLUME
MUTE
CODE SET
POWER
STANDBY
DVDMENU
Flashes
twice.
TV
VOLUME
MUTE
CODE SET
A/B/C/D/E
+
100
+
10
1
3
CD
TUNER
TAPE/MD
DVD/LD
TV/DBS
VCR
PHONO
V-AUX
EXT. DEC.
MOVIE
THEATER 1
MOVIE
THEATER 2
MONO MOVIE
/DTS
SURROUND
DISCO
TV SPORTS
ROCK
CHURCH
JAZZ CLUB
CLEAR
ENTER
HALL
TEST
2
5
8
4
7
0
9
6
POWER
STANDBY
VCR
Flashes
twice.
TV
VOLUME
MUTE
CODE SET
A/B/C/D/E
+
100
+
10
1
3
CD
TUNER
TAPE/MD
DVD/LD
TV/DBS
VCR
PHONO
V-AUX
EXT. DEC.
MOVIE
THEATER 1
MOVIE
THEATER 2
MONO MOVIE
/DTS
SURROUND
DISCO
TV SPORTS
ROCK
CHURCH
JAZZ CLUB
CLEAR
ENTER
HALL
TEST
2
5
8
4
7
0
9
6
POWER
STANDBY
DVDMENU
Flashes
twice.
REMOTE CONTROLLER