Yamaha CBX-K2 - Manual (Page 20)

20
Reference
Using the SHIFT-Related Functions
The enormous flexibility and power of the CBX-K2 is in its
“hidden” or SHIFT-related functions — allowing you to
send virtually any kind of MIDI message directly from the
keyboard or use the Assignable Wheel/Slider for real-time
control change.
In the instructions that follow, “ L” refers to either of
the ENTER keys, J or K. In other
words, this means that either key can be used, unless
indicated otherwise.
NOTE ■ Both N / M
lamps flash briefly when a function is executed. The
LED display flashes briefly when a MIDI message is
sent.
The MIDI functions can be generally divided into three
types, according to their operation.
1) Holding C and pressing the function’s key. For
these functions, such as Sequencer Stop and Start,
pressing
L is not necessary. These functions are
shown on the panel without underline.
2) Holding C, pressing the function’s key and then
L. These functions are indicated with a dashed
underline on the panel (for example, GM ON and XG
ON) and require pressing
L to execute.
3) Holding C, pressing the function’s key, entering
a value and then pressing L. These functions
are indicated with an underline on the panel (for ex-
ample, PROGRAM CHANGE and TEMPO), and
require that a value (Decimal or Hexadecimal) be
entered.
When changing a function, the LED display indicates
the on/off status or the value of the function.
Many of the functions can be done with one or two key-
strokes, while others require you to enter a number value
and press one of the
L keys to execute the function.
All functions can be accessed or executed by using one of
the operations described below.
In using the SHIFT-related functions, remember
Keep holding down C until the end of the
operation. If C is released in mid-operation,
you’ll have to start the operation all over again.
SEQUENCER PROGRAM SYSTEM WHEEL ASSIGN
STOP
SONG SELECT
START TEMPO CONTINUE
B MEASURE TOP BOTTOM TIME SIGNATURE
FIXED VELOCITY MIDI CH MERGE ON/OFF SOUND OFF XG ON GM ON
VOICE MAP POLY/ MONO
BANK SELECT PROGRAM CHANGE
CHANNEL MERGE RESET CONTROL TG300B RESET SOUND OFF ALL CH DEVICE NUMBER TOUCH SENSITIVITY
RPN NRPN DRUM NUMBER CONTROLLER
RPN NRPN DATA DENSITY MSB 1ST/ LSB 1ST FOOT SW ASSIGN CONTROLLER
SLIDER ASSIGN
RPN NRPN DRUM NUMBER CONTROLLER
DATA DENSITY PB DENSITY
RESET TRANSPOSE
1 MODULATION 2 BREATH 5 PORTA TIME 6 DATA ENTRY 7 VOLUME 10 PANPOT
11 EXPRESSION 64 HOLD1(DAMPER) 65 PORTAMENTO 71 HARMONIC 72 RELEASE TIME 73 ATTACK TIME 74 BRIGHTNESS 84 PORTA CTRL
123 VIBRATO RATE 124 VIBRATO DEPTH 125 VIBRATO DELAY 126 LP FILTER CUTOFF 127 LP FILTER RESONANCE 128 HP FILTER CUTOFF 129 EQ LO GAIN 130 EQ HI GAIN
131 EQ LO FREQUENCY 132 EQ HI FREQUENCY 133 EG ATTACK TIME 134 EG DECAY TIME 135 EG RELEASE TIME 136 DRUM LP FILTER CUTOFF 137 DRUM LP FILTER RESONANCE 138 DRUM EG ATTACK RATE
139 DRUM EG DECAY RATE 140 DRUM PITCH COARSE 141 DRUM PITCH FINE 142 DRUM LEVEL 143 DRUM PAN 144 DRUM REVERB 145 DRUM CHORUS 146 DRUM VARIATION
147 DRUM HP FILTER CUTOFF 148 DRUM EQ LO GAIN 149 DRUM EQ HI GAIN 150 DRUM EQ LO FREQUENCY 151 DRUM EQ HI FREQUENCY
91 REVERB 93 CHORUS 94 VARIATION
120 PB SENSITIVITY
121 FINE TUNE
122 COARSE TUNE
CONTROLLER NUMBER LIST CONTROL CHANGE
ENTER
HEXA DECIMAL DECIMAL 1 2 3 4 5 6 7 8 9 A B C D E F 0 B
RPN
NRPN 152 CH PRESSURE 153 KEY PRESSURE 154 MASTER VOLUME 156 MASTER TUNING 157 VELOCITY 158 TEMPO
OTHERS
L
keys
MIDI functions
(Group A and Group B) Value entry
(Decimal and Hexadecimal)
Displays current setting or value.
Display
ç key
Reference