Yamaha DSP-AX3200 - Manual (Page 41)

39
English
INTR
ODUCTION
PREP
ARA
TION
B
ASIC OPERA-
TION
AD
V
ANCED
OPERA
TION
ADDITIONAL
INFORMA
TION
APPENDIX
REMOTE CONTROL FEATURES
5 Press the button for which you want to
program the new function.
“LEARN” is displayed.
6 Press and hold the button on the other
remote control that has the function you
want to program into this remote control
until “OK” appears in the display window.
Notes
• “NG” appears in the display window when programming has
not been done correctly. In this case, start over from step 5.
• This remote control can learn approximately 120 functions.
However depending on the signals learned, “FULL” may
appear in the display window much earlier than this number. In
this case, clear unnecessary programmed functions to make
further learning on the remote control.
7 Repeat steps 5 and 6 to program additional
functions.
8 Press LEARN again to exit from the learning
mode.
Notes
• It is also possible to program in the control area of this unit
with 10KEY/DSP set to DSP. However, if you program
functions in this area, you cannot control this unit and select a
DSP program.
• If the batteries in the other remote control are weak, they may
not have enough power to transmit signals to this remote
control.
• When the remote controls are either too close together or too
far apart, you may not be able to program this remote control.
• Direct sunlight interferes with infrared rays.
• “ERROR” appears in the display window in the following
circumstances:
– when pressing more than one button at once; or
– when MACRO ON/OFF is switched to another position.
Programming a New Remote
Control Function (Learn Feature)
If you want to program functions not included in the basic
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. The possible
programming area is the same as a component control
area, so the buttons are programmable independently for
each source component area.
Note
• This remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn
most of the other remote control’s functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
1 Set 10KEY/DSP to 10KEY.
2 Press an input selector button, Å or ı to
select a source component.
3 Place this remote control and the other
remote control about 5 to 10 cm apart on a
flat surface so that their infrared transmitters
are aimed at each other.
4 Press LEARN by using a ballpoint pen or
similar object.
Do not press and hold LEARN longer than three
seconds. Otherwise this unit enters the manufacturer
code setting mode.
Note
• If you do not press any button within 30 seconds during steps 5
and 6, the learning process is canceled. If this happens, start
over from step 4.
TRANSMIT
RE-NAME
ST ANDBY
6CH INPUT
SYSTEM
CLEAR
LEARN
MA
CR
O
OFF
O N
MA
CR
O
PHONO
A
B
CD DV
D
VCR2/D
VR
VCR 1 TITLE
SOURCE
ENTER
D-TV/LD
CBL/SA
T
CD-R
MD/T
APE
TUNER
V-
A
U X
PO
WER
5 to 10 cm (2 to 4 inch)
TRANSMIT
RE-NAME
ST ANDBY
6CH INPUT
SYSTEM
CLEAR
LEARN
MA
CR
O
OFF
ON
MA
CR
O
PHONO
A
B
CD DV
D
VCR2/D
VR
VCR 1 TITLE
SOURCE
ENTER
D-TV/LD
CBL/SA
T
CD-R
MD/T
APE
TUNER
V-
A
U X
PO
WER
LEARN
LEARN
TRANSMIT
RE-NAME
ST ANDBY
6CH INPUT
SYSTEM
CLEAR
LEARN
MA
CR
O
OFF
O N
MA
CR
O
PHONO
A
B
CD DV
D
VCR2/D
VR
VCR 1 TITLE
SOURCE
ENTER
D-TV/LD
CBL/SA
T
CD-R
MD/T
APE
TUNER
V-
A
U X
PO
WER DSP 10KEY
Flashes alternately
PHONO A B
CD
DVD VCR2/DVR VCR 1 D-TV/LD CBL/SAT
CD-R MD/TAPE TUNER V-AUX