XtremeMac Luna Room Audio System - Manual (Page 9)

LUNA™ User Manual 1 LUNA™ User Manual 1
To Preview Alarm Settings:
Luna features an alarm preview which allows you to hear and see all of your
set alarm options – audio source, volume and volume ramping, and dimmer
settings. This way you have no surprises in the morning!
1. Push the Right Control Knob to access the main menu. The menu will
appear on Luna’s display.
2. Turn the Right Control Knob to highlight either “Alarm 1” or “Alarm 2”
and push to select.
3. Turn the Right Control Knob until the “Preview” menu item is highlighted
and push to select. Luna will then let you preview all of your alarm
settings, including source, volume/ramping and dimmer.
4. Preview will last for 30 seconds and then time out. To end preview, press
the Right Control Knob.
Alarm Operation
1. Set the alarm time and options following the instructions in “SETTING
THE ALARMS”
2. Push the Alarm 1 Button on the back left to activate/deactivate Alarm 1
and/or push the Alarm 2 Button on the back right to activate/deactivate
Alarm 2. The display will show each alarm time and source icon when
activated.
3. When the alarm is sounding, the alarm time and source icon will flash.
You can snooze, reset the alarm for the next day, or turn the alarm
completely off.
4. Push the Left Control Knob to snooze. Your alarm settings allow you to
set the snooze time in advance, but the snooze time can be adjusted
when in snooze mode by turning the Left Control Knob.
5. Push the Right Control Knob to silence the alarm and reset it to come on
again the following day .
6. To stop the alarm from sounding on the following day, push the
corresponding Alarm On/Off Button. This will turn the alarm OFF. The
alarm time and source icon will not appear in the display.
7. If the alarm is not turned off after it sounds it will play for approximately
one hour and then turn off automatically. The alarm will reset for the
following day unless you turn the alarm off.
Listening to Audio
Many of the functions can be controlled by the included remote control.
Please review the “REMOTE CONTROL” section on pages 10-11 to learn
more about using the remote.
Listening to Your iPod:
1. Select the correct insert and dock your iPod (see “Universal Dock Well”
on page 7).
2. Push the Left Control Knob to toggle through source options until “iPod”
appears in the display.
3. Press play on your iPod.
4. Turn the Left Control Knob to increase/decrease the volume.
Note: If you have a iPod without a dock connector, please follow the
instructions for “Listening to an Auxiliary Source” below.
Listening to the Radio:
1. Push the Left Control Knob to toggle through source options until “FM”
or “AM” appears in the display. The frequency will blink to indicate that it
can be adjusted.
2. Turn the Right Control Knob to tune to the desired frequency and push to
select.
3. Turn the Left Control Knob to increase/decrease the volume.
4. To select a new station or a preset station, hold down the Left Control
Knob to access the Radio menu. Turn the right control knob to scroll
through the menu options – “Tune”, “Select Presets” and “Set Presets.”
5. When the desired menu item is highlighted, push the Right Control Knob
to select and follow the instructions below:
Tune
– The AM/FM band indicator will blink to indicate that it can be
adjusted. Turn the Right Control Knob to the desired band and
push to select. The frequency will then blink to indicate it can be
adjusted.
– Turn the Right Control Knob to tune the desired frequency and
push to accept.
Set Presets
– Turn the Right Control Knob until the desired preset number is
highlighted (presets 1 through 4) and push to select.
– The AM/FM band indicator will blink to indicate it can be adjusted.
Turn the Right Control Knob to the desired band and push to
select. The frequency will then blink to indicate that it can be
adjusted.
– Turn the Right Control Knob to tune the desired frequency and
push to accept.
– Repeat these steps to program remaining presets.
Select Presets
– Turn the Right Control Knob until the desired preset number is
highlighted (presets 1 through 4) and push to select.
Note: You can also access all radio functions though the main menu
under “Radio.”
Listening to an Auxiliary Source:
1. Connect the device to “AUX/LINE IN” jack on the back of Luna with an
auxiliary 3.5mm stereo audio cable (not included)
2. Push the Left Control Knob to toggle through source options until “AUX”
appears in the display.
3. Press play on the device.
4. Turn the Left Control Knob to increase/decrease the volume.
Adjusting Bass and Treble:
1. Push the Right Control Knob to access the main menu. The menu will
appear on Luna’s display.
2. Turn the Right Control Knob until the “Settings” menu item is highlighted
and push to select.
3. Turn the Right Control Knob until the “Audio” menu item is highlighted
and push to select.
4. Turn the Right Control Knob to highlight either “Bass” or “Treble” and
push to select. The level will blink to indicate that it can be adjusted.
5. Turn the Right Control Knob to increase/decrease the level (from -7 to 7)
and push to accept.
Note: It is recommended that you adjust the bass and treble while listening
to an audio source.