Agri-Fab LST42B - Manual (Page 28)

28
PARTS TO REMOVE AT END OF SEASON
• Remove the clutch/idler assembly. (The two hanger
brackets and the two shoulder bolts may be left
attached to the tractor frame.)
• Remove the drive belt from the engine pulley.
• If you replaced the engine pulley keeper on a manual
attachment clutch tractor, reinstall the tractor's original
engine pulley keeper. See fi gure 33 on page 16 or
fi gure 39 on page 18.
• If you have a rod operated attachment clutch, remove
the engagement rod from the tractor's clutch arm. See
fi gure 29 on page 15.
• If a rear mounted attachment is to be used, remove
the rear weight tray, leaving the bolts that you installed
in the sides of the tractor draw bar. Retighten the
bolts.
• If a front mounted attachment is to be used, remove
the side plates from the tractor. Be sure to assemble
bolts back into the empty holes in the tractor frame.
STORAGE RECOMMENDATIONS
• Lower the snow thrower to the ground.
• Remove the snow thrower from the tractor.
• Clean the snow thrower thoroughly. Wash off any salt
deposit which may have dried on the thrower and
housing.
• Any bare metal that has become exposed should be
painted or coated with a light oil to prevent rust.
• Store in a dry place.
REMOVING THE SPIRAL AUGER HOUSING
• Lower the snow thrower to the ground.
• Remove the attachment pin. See fi gure 54 on page
23.
• Lock the snow thrower's lift handle in the down
position to decrease belt tension.
• Release the spring tension from the auger belt idler
arm on the bottom of the clutch/idler assembly.
• Remove the auger drive belt from the clutch/idler
assembly. See fi gure 56 on page 23.
• Pull the spiral auger housing assembly off of the
tractor.
CAUSE PROBLEM CORRECTION
Clogged discharge chute Clogged discharge chute
Spiral augers don't turn
Snow thrower stalls tractor engine
TROUBLESHOOTING
STORAGE
1. Upper or lower V belt too loose 1. Increase tension on V belt 1. Upper or lower V belt too loose 1. Increase tension on V belt
2. Upper or lower V belt broken 2. Replace V belt 2. Upper or lower V belt broken 2. Replace V belt
3. Shear bolts are sheared. 3. Replace shear bolts 3. Shear bolts are sheared. 3. Replace shear bolts
1. Tractor ground speed too fast 1. Use lower tractor gear 1. Tractor ground speed too fast 1. Use lower tractor gear
2. Tractor throttle set too low 2. Increase to full throttle 2. Tractor throttle set too low 2. Increase to full throttle
3. Snow too deep 3. Raise the snow thrower 3. Snow too deep 3. Raise the snow thrower
4. Snow melts during contact with 4. Allow snow thrower to cool to 4. Snow melts during contact with 4. Allow snow thrower to cool to
the snow thrower outdoor temperature before using the snow thrower outdoor temperature before using
Front wheels slide instead of steering Front wheels slide instead of steering
Snow thrower rides up over snow Snow thrower rides up over snow
1. Object jammed in spiral auger 1. Stop engine, disengage the snow 1. Object jammed in spiral auger 1. Stop engine, disengage the snow
thrower clutch and clear the auger thrower clutch and clear the auger
2. Hard or heavy snow 2. Increase to full throttle and 2. Hard or heavy snow 2. Increase to full throttle and
decrease ground speed decrease ground speed
Not enough traction at front wheels 1. Increase scraper plate clearance Not enough traction at front wheels 1. Increase scraper plate clearance
by lowering skid shoes by lowering skid shoes
2. Pull down on lift handle to 2. Pull down on lift handle to
increase weight on front wheels increase weight on front wheels
1. Tractor ground speed too fast 1. Reduce ground speed 1. Tractor ground speed too fast 1. Reduce ground speed
2. Bottom snow is icy or hard packed 2. Lower the skid shoes so that front 2. Bottom snow is icy or hard packed 2. Lower the skid shoes so that front
of skid shoe is lower than the rear of skid shoe is lower than the rear