ASSISTANT AH-1023 - Manual

2. CLOCK OPERATING
Blinking Display/PM Indicator/Alarm
Indicator
When the clock is plugged in, the display
will blink on and off meaning that incorrect
time is being displayed. You should always
check the time, when this is indicated. The
clock will automatically indicate AM/PM, but
you must be sure to set the indicator for the
time of alarm correctly. When the PM indicator
is on, it is “PM”, when it is off, it indicates “AM”.
When the Alarm indicator is on, the alarm will
sound at the time set.
3. TIME SETTING
Press and hold the [TIME] button and the
[HOUR] button until the correct hour is displayed
(and the AM/PM is correct), then release the
[HOUR] button and press the [MINUTE] button
until the correct minutes are displayed.
4. ALARM SETTING
Press and hold the [ALARM] but-
ton and the [HOUR] or the
[MINUTE] button as above. Be sure the set the
AM/PM properly too.
5. TO OPERATE THE ALARM
Slide the [ALARM ON/OFF] switch to the “ON”
position. The alarm will sound at the time set. To
shut off the alarm, slide the [ALARM ON/OFF]
switch to the “OFF” position.
6. SNOOZE
Press the [SNOOZE] button and get extra 8~9
minutes of sleep.
7. HI/LOW DIMMER SWITCH
If more intense display is preferred, slide
the [DIMMER HI/LOW] switch to the “HI” po-
sition. If less intense display is desired, slide
the [DIMMER HI/LOW] switch to the “LOW”
position.
8. BATTERY BACKUP
Insert one 9V battery into the battery compart-
ment on the back side of the clock. The battery will
hold the alarm and time setting until the power is
restored. If there is no battery and the power is in-
terrupted, the display will fl ash and the alarm and
the time will need to be reset.
9. MAINTENANCE
A soft cloth or a paper towel may be used to
clean the clock. Do not use any corrosive cleansers
ENGLISH – 2 – ENGLISH
1. APPEARANCE
1. ALARM indicator
2. PM indicator
3. [SNOOZE] button
4. [HOUR] button
5. [MINUTE] button
6. [TIME] button
7. [ALARM] button
8. [ALARM ON/OFF] switch
9. [DIMMER HI/LOW] switch
OPERATION MANUAL
ENGLISH – 3 – ENGLISH
or chemical solutions on the clock. Keep the clock
clean and dry to avoid any problems.
10. SAFETY INSTRUCTIONS
- The device should not be exposed to water or
moisture.
- No objects fi lled with liquids, such as vases,
shall be placed on the device.
- Ventilation: The device should be situated so
that its location or position does not interfere
with proper ventilation. For example, the appli-
ance should not be placed on a bed, sofa, rug, or
similar surfaces that may block the ventilation
openings.
- The device should be situated away from heat
sources such as radiators, heat registers, stoves, or
other appliances (including amplifi ers) that pro-
duce heat.
- Power cord protection: Power supply cords
should be routed so that they are not likely to
be walked on pinched by items placed upon or
against them, paying particular attention to cords
at plugs, convenience receptacles and the point
where they exit from the device.
- Disconnect the device from the mains supply
when not in use.
- To avoid the risk of eclectic shock, do not re-
move the cover of the device. There are no ser-
viceable parts inside.
- Do not operate this product, if the mains lead
is damaged. The mains lead should be replaced by
the manufacturer or its appointed agent.
- Please, read this operation manual before use
and retain for future reference.
- During the electro static discharge the product
may auto reset, then adjust the mode to return to
the normal operation.
ENGLISH – 4 – ENGLISH
ENGLISH – 6 – ENGLISH ENGLISH – 7 – ENGLISH ENGLISH – 5 – ENGLISH
ENGLISH – 1 – ENGLISH
DESKTOP LED CLOCK
Model AH-1023
WWW.TIWELL.COM
WWW.ASSISTANT.UA