Hama EWS-870 - Manual (Page 6)

10 11
DAYLIGHT SAVING TIME (DST)
The clock has been programmed to automatically
switch when daylight saving time is in effect.
Your clock will display “DST” on the LCD during
the summer.
TIME AND CALENDAR SETTING
If the clock does not receive the time signal
successfully, you can set the time manually. As
soon as the transmitter is received again, the
clock will automatically synchronize with the
received time.
1. In normal mode, press and hold “DISPLAY
SET” key for 3 seconds until the Hour format
digit fl ashing.
2. Press “+” / “-” key to select 12/24 hour format.
3. Press “DISPLAY SET” key again to step
the setting item to Hour with the Hour digit
fl ashing.
4. Press “+” / “-” key to adjust the value of the
fl ashing digit.
5. Do the above operation in this sequence: 12/24
Hr > Hour > Minute > Second > Time zone.
6. Press and hold “” key for 3 seconds to save
and exit the setting.
Note:
If your local time is different from the RC received
time, you can set the desired time zone. The
available time difference is from -23 hours to +23
hours. After setting the desired time difference,
the clock will show the time that RC received
time plus/minus the time difference.
ALARM TIME SETTING
1. In normal mode, press and hold “ALARM SET”
key for 3 seconds until the Hour digit fl ashing.
2. Press “+” / “-” key to adjust the value of the
fl ashing digit.
3. Press “ALARM SET” key again to step the
setting value to Minute with the Minute digit
fl ashing.
4. Press “+” / “-” key to adjust the value of the
fl ashing digit.
5. Press “ALARM SET” key to save and exit the
setting.
Note:
1. In alarm mode, the “AL” icon will display on
the LCD.
2. The alarm function will turn on automatically
once you set the alarm time.
USING ALARM AND SNOOZE FUNCTION
1. Set the desired alarm time as described in the
above section.
2. Or press “ALARM SET” key to display the
alarm time, press it again to turn on alarm
function with the alarm icon “ ” displayed on
the LCD.
3. When clock reach the alarm time, alarm
sound will start. Where, it can be stopped by
following operation:
a). Auto-stop after two minutes alarming if
without any operation and it will re-alarm by
the next day.
b). By pressing “SNOOZE” key to enter snooze
that the alarm will sound again after 5 minutes.
c). By pressing “ALARM SET” key to turn off the
alarm function.
Note:
1. The snooze could be used continuously in 24
hours.
2. During the snooze, the alarm icon will keep
fl ashing.
VIEW THE CHANNEL
1. The default displayed channel is channel 1.
In normal mode, press “+CH” key to check
the outdoor temperature from channel 1 to
channel 3.
2. Press and hold “+/CH” key for 3 seconds to
turn to channel auto-change mode that the
channels change automatically.
3. Press “+/CH” key again to return to nomal
mode.
Note:
In channel auto-change mode, channel and its
outdoor temperature changes automatically in
every 4 second.
READING INDOOR&OUTOOR TEMPERATURE
RECORDS
1. Push “°C/°F” switch to change the
temperature unit to Celsius or Fahrenheit.
2. Press “CH/+” key to change the channels
among 3 channels and check their
temperature.
Note:
1. Once the channel is assigned to one
transmitter, you can only change it by
removing the batteries or resetting the unit.
2. If no signals are received or the transmission
is interfered, “---” will appear on the LCD.
3. Relocate the clock or the transmitter in other
positions and make sure the transmission is
within the effective range of 50 meters approx.
4. After several trials in vain, please reset
the clock thoroughly. Try out where your
multifunctional alarm clock receives the
signals best.
Normal mode 12/24 Hr setting
Time zone
setting
Hour setting
Minute setting
Second setting
Alarm time
mode
Hour setting Minute setting
Channel 1 Channel 2 Channel 3
00113984man_cs_de_el_en_es_fr_hu_it_nl_pt_ru_sk.indd 10-11 10.01.13 10:30