MIDLAND XTC-100 action camera - Manual (Page 2)

P
XTC-100 Action Camera
Thank you for your purchase of the XTC-100 Action Camera. As someone who seeks adventure, we are proud to
offer you the ultimate tool in capturing and recording your adventures. With easy to use one switch operation, 140
degree algle lens and 2 hour battery life you never miss a minute of the action. Once captured, simply connect to
your computer and upload the videos to share with friends. It is that simple! Enjoy!
What’s in the box
› Midland XTC-100 Action camera
› 2 GB Micro SD card
› 2 AAA Alkalinebatteries
› USB cable
› Goggle mount
› Helmet adhesive mount
› Dual Track mount for goggle mount and helmet adhesive mount.
› Helmet strap mount
› Bicycle handlebar mount
XTC-100 Features and Controls
Features:
› 640x480 resolution (4:3 aspect ratio)
› Records as AVI
› 30 frames per second
› 140 degree angle lens
Quick Start Guide
1. Open battery door and install batteries observing polarity. Replace battery cover.
2. Open and fold down back rubber cover. Insert micro Sd card observing proper direction. Close cover.
3. Move RECORD switch forward, recording will start in 8 seconds.
4. To stop recording, slide switch back to the off position.
5. Plug in camera to computer and download video.
Getting to Know the XTC-100
Batteries
1. To insert the batteries, push down the battery door latch on the right side of
the camera. Door will release. Push forward to remove.
2. Install 2 AAA batteries observing polarity.
3. Return battery door and click into place.
Battery Status Indicator Meaning
Solid Green Indicates full battery life
Solid Red Indicates half battery life
Blinking Red* Indicates low battery life
No Light Batteries are dead
Note: When the red battery LED begins blinking, be prepared to change the batteries because the camera will stop
recording at this point.
Micro SD Card
1. Open and fold down the back rubber cover.
2. Insert Micro SD card into slot observing proper direction (shown sideways).
3. Return rubber flap into place.
Recording
1. Move the RECORD switch forward. This turns the camera on.
2. The battery indicator will light from red to green. The SD card indicator will light green. The record indicator will begin
flashing red after 8 seconds. This indicates the camera is capturing video.
3. To stop recording, move the RECORD switch back to the off position.
Note: The camera will continue recording for 3 seconds after toggling the switch to the off position.
SD card LED Status Meaning
Green 1 GB or more avai lable
Orange 512 MB to1 GB available
Red Below 512 MB available or no MicroSD card installed.
Flashing Red Cannot read the card
Flashing Green Indicates card has been reformatted.
Memory Size Record Time
512 MB 7.5 Minutes
1 GB 15 Minutes
2 GB 30 Minutes
4 GB 60 Minutes
8 GB 120 Minutes
16 GB 240 Minutes
32 GB 480 Minutes
Note: The camera automatically splits the video into 2 GB segments.
Camera Mounting
Mount on Dual Track System
The XTC-100 was innovatively designed with an identi-
cal dual track mount system on either side of the came-
ra. This allows an ease of installation.
To mount the camera on the dual track mount, slide the
camera onto the dual track system with the two notches
on the mount facing towards the back of the camera.
To detach the camera from the dual track mount, hold
the camera with the lens facing away from you. Press
down the mount release switch and pull the mount to-
wards yourself.
The dual track mount allows the camera to be easily
mounted on both helmet mount and goggle mount. This
elimi nates the hassle of having to remount the camera
every time.
When mounting the camera on the dual track mount, you
must do the following:
1. Consider what you would like to shoot and use the
helmet mount or goggle mount accordingly.
2. Ensure, once attached, that the camera is aimed
straight and not towards the ground or at the sky.
Mount using the Thread Mount
On the bottom of the XTC-100 is a standard thread
mount that allows the camera to be mounted to an hel-
met strap mount or to a bicycle handlebar mount.
To fix the camera, insert the screw on the mount into
the camera thread and rotate the camera clockwise to
tighten down onto the screw.
When mounting the camera on the handlebars of a
bike or with the vented helmet strap mount follow these
steps:
1. Consider what you would like to shoot and mount
accordingly.
2. Ensure, once attached, that the camera is aimed
straight and not towards the ground or at the sky.
Compatible Systems
The XTC-100 can be used on both Windows operating system and MAC.
The camera records as AVI.
Downloading Videos
There is no need to install any software with the XTC-100. It is a plug and play device.
Ensure batteries are new or fully charged before downloading video.
Connect the camera to the USB port using the included cable.
The camera will be automatically recognized as external hard drive (USB key)
All your videos will be saved into the DCIM folder.
Reformatting the Micro SD card
The Micro SD card can be reformatted while in the camera. This allows you to delete all the videos at one time. Follow
these steps:
1. Move the RECORD switch to the record position.
2. When the battery indicator turns green, press and hold the Micro SD card reformat button.
3. Keep the Micro SD card reformat button down until the record indicator turns off and the SD card indicator begins
blinking green.
4. Move the RECORD switch to the off position.
Note: The camera cannot reformat the Micro SD card if the low battery light is on. Ensure new batteries are instal-
led in the camera before attempting the reformat process.
Tips and Tricks
Problem Solution
Batteries
Camera not turning on Ensure the batteries are installed properly observing polarity.
Make sure batteries are new or fully charged.
Recording
Camera not recording Make sure the switch is pushed all the way forward. If the record LED does not
come on, turn off the device and reinstall the batteries.
Verify available memory.
Micro SD card
Micro SD card not reading Ensure the Micro SD card is inserted properly.
Plug camera into the computer to verify it has available storage.
Attempt formatting process.
Video Playback
Slow or choppy video Verify the camera is plugged into a USB 2.0 device.
Remove other unused USB devices.
Transfer video to computer before viewing.
Video Downloading
Slow data transfer Verify the camera is plugged into a USB 2.0 device. If registering as 1.1, unplug and
the re-plug the device.
Remove other unused USB devices.
Computer does notrecognize ca-
mera
Ensure record switch is in the record position while connected to computer.
Ensure the Micro SD card is inserted properly.
Micro SD card may becorrupted. Attempt formatting process.
Sound
Excessive Wind Noise Place piece of tape over microphone hole.
Limited Warranty
Midland Radio Corporation will repair or replace, at its option without charge, any Midland XTC-100 Action camera
which fails due to a defect in material or workmanship within TWO Years following the initial consumer purchase.
This warranty does not apply to accidents of any kind, exposure to pressure, extreme temperatures (outside of -10°C to
45°C), and submersion water damage as this product is water resistant but not waterproof, battery leak or abuse.
Accessories have a 90 day warranty from date of purchase, inclu ding any mounts and cables. This warranty does not
include the cost of labor for removal or re-installation of the product in a vehicle or other mounting.
Hereby, CTE International declares that this XTC-100 is in compliance with the essential requirements and other rele-
vant provisions the Electromagnetic Compatibility Directive 2004/108/CE. A copy of Declaration of Conformity can be
found at: www.midlandradio.eu
140° degree glass lens
Microphone
Dual track mounting system
Record switch
forward: on/record
Record led
flashes red when
camera is recording
Battery led
Record switch
backward:
Off/Stop recording
SD Card led
Mini USB connector
SD Card
reformat button
Mini SD Card slot
Camera thread Mounting screw
Helmet strap mount Bicycle handle bar mount
dual track system mount
Release button
Helmet adhesive mount Goggle mount
G R
XTC-100 Action Camera
Thank you for your purchase of the XTC-100 Action Camera. As someone who seeks adventure, we are proud to
offer you the ultimate tool in capturing and recording your adventures. With easy to use one switch operation, 140
degree algle lens and 2 hour battery life you never miss a minute of the action. Once captured, simply connect to
your computer and upload the videos to share with friends. It is that simple! Enjoy!
What’s in the box
› Midland XTC-100 Action camera
› 2 GB Micro SD card
› 2 AAA Alkalinebatteries
› USB cable
› Goggle mount
› Helmet adhesive mount
› Dual Track mount for goggle mount and helmet adhesive mount.
› Helmet strap mount
› Bicycle handlebar mount
XTC-100 Features and Controls
Features:
› 640x480 resolution (4:3 aspect ratio)
› Records as AVI
› 30 frames per second
› 140 degree angle lens
Quick Start Guide
1. Open battery door and install batteries observing polarity. Replace battery cover.
2. Open and fold down back rubber cover. Insert micro Sd card observing proper direction. Close cover.
3. Move RECORD switch forward, recording will start in 8 seconds.
4. To stop recording, slide switch back to the off position.
5. Plug in camera to computer and download video.
Getting to Know the XTC-100
Batteries
1. To insert the batteries, push down the battery door latch on the right side of
the camera. Door will release. Push forward to remove.
2. Install 2 AAA batteries observing polarity.
3. Return battery door and click into place.
Battery Status Indicator Meaning
Solid Green Indicates full battery life
Solid Red Indicates half battery life
Blinking Red* Indicates low battery life
No Light Batteries are dead
Note: When the red battery LED begins blinking, be prepared to change the batteries because the camera will stop
recording at this point.
Micro SD Card
1. Open and fold down the back rubber cover.
2. Insert Micro SD card into slot observing proper direction (shown sideways).
3. Return rubber flap into place.
Recording
1. Move the RECORD switch forward. This turns the camera on.
2. The battery indicator will light from red to green. The SD card indicator will light green. The record indicator will begin
flashing red after 8 seconds. This indicates the camera is capturing video.
3. To stop recording, move the RECORD switch back to the off position.
Note: The camera will continue recording for 3 seconds after toggling the switch to the off position.
SD card LED Status Meaning
Green 1 GB or more avai lable
Orange 512 MB to1 GB available
Red Below 512 MB available or no MicroSD card installed.
Flashing Red Cannot read the card
Flashing Green Indicates card has been reformatted.
Memory Size Record Time
512 MB 7.5 Minutes
1 GB 15 Minutes
2 GB 30 Minutes
4 GB 60 Minutes
8 GB 120 Minutes
16 GB 240 Minutes
32 GB 480 Minutes
Note: The camera automatically splits the video into 2 GB segments.
Camera Mounting
Mount on Dual Track System
The XTC-100 was innovatively designed with an identi-
cal dual track mount system on either side of the came-
ra. This allows an ease of installation.
To mount the camera on the dual track mount, slide the
camera onto the dual track system with the two notches
on the mount facing towards the back of the camera.
To detach the camera from the dual track mount, hold
the camera with the lens facing away from you. Press
down the mount release switch and pull the mount to-
wards yourself.
The dual track mount allows the camera to be easily
mounted on both helmet mount and goggle mount. This
elimi nates the hassle of having to remount the camera
every time.
When mounting the camera on the dual track mount, you
must do the following:
1. Consider what you would like to shoot and use the
helmet mount or goggle mount accordingly.
2. Ensure, once attached, that the camera is aimed
straight and not towards the ground or at the sky.
Mount using the Thread Mount
On the bottom of the XTC-100 is a standard thread
mount that allows the camera to be mounted to an hel-
met strap mount or to a bicycle handlebar mount.
To fix the camera, insert the screw on the mount into
the camera thread and rotate the camera clockwise to
tighten down onto the screw.
When mounting the camera on the handlebars of a
bike or with the vented helmet strap mount follow these
steps:
1. Consider what you would like to shoot and mount
accordingly.
2. Ensure, once attached, that the camera is aimed
straight and not towards the ground or at the sky.
Compatible Systems
The XTC-100 can be used on both Windows operating system and MAC.
The camera records as AVI.
Downloading Videos
There is no need to install any software with the XTC-100. It is a plug and play device.
Ensure batteries are new or fully charged before downloading video.
Connect the camera to the USB port using the included cable.
The camera will be automatically recognized as external hard drive (USB key)
All your videos will be saved into the DCIM folder.
Reformatting the Micro SD card
The Micro SD card can be reformatted while in the camera. This allows you to delete all the videos at one time. Follow
these steps:
1. Move the RECORD switch to the record position.
2. When the battery indicator turns green, press and hold the Micro SD card reformat button.
3. Keep the Micro SD card reformat button down until the record indicator turns off and the SD card indicator begins
blinking green.
4. Move the RECORD switch to the off position.
Note: The camera cannot reformat the Micro SD card if the low battery light is on. Ensure new batteries are instal-
led in the camera before attempting the reformat process.
Tips and Tricks
Problem Solution
Batteries
Camera not turning on Ensure the batteries are installed properly observing polarity.
Make sure batteries are new or fully charged.
Recording
Camera not recording Make sure the switch is pushed all the way forward. If the record LED does not
come on, turn off the device and reinstall the batteries.
Verify available memory.
Micro SD card
Micro SD card not reading Ensure the Micro SD card is inserted properly.
Plug camera into the computer to verify it has available storage.
Attempt formatting process.
Video Playback
Slow or choppy video Verify the camera is plugged into a USB 2.0 device.
Remove other unused USB devices.
Transfer video to computer before viewing.
Video Downloading
Slow data transfer Verify the camera is plugged into a USB 2.0 device. If registering as 1.1, unplug and
the re-plug the device.
Remove other unused USB devices.
Computer does notrecognize ca-
mera
Ensure record switch is in the record position while connected to computer.
Ensure the Micro SD card is inserted properly.
Micro SD card may becorrupted. Attempt formatting process.
Sound
Excessive Wind Noise Place piece of tape over microphone hole.
Limited Warranty
Midland Radio Corporation will repair or replace, at its option without charge, any Midland XTC-100 Action camera
which fails due to a defect in material or workmanship within TWO Years following the initial consumer purchase.
This warranty does not apply to accidents of any kind, exposure to pressure, extreme temperatures (outside of -10°C to
45°C), and submersion water damage as this product is water resistant but not waterproof, battery leak or abuse.
Accessories have a 90 day warranty from date of purchase, inclu ding any mounts and cables. This warranty does not
include the cost of labor for removal or re-installation of the product in a vehicle or other mounting.
Hereby, CTE International declares that this XTC-100 is in compliance with the essential requirements and other rele-
vant provisions the Electromagnetic Compatibility Directive 2004/108/CE. A copy of Declaration of Conformity can be
found at: www.midlandradio.eu
140° degree glass lens
Microphone
Dual track mounting system
Record switch
forward: on/record
Record led
flashes red when
camera is recording
Battery led
Record switch
backward: Off/Stop recording
SD Card led
Mini USB connector
SD Card
reformat button
Mini SD Card slot
dual track system mount
Release button
Helmet adhesive mount Goggle mount
Camera thread Mounting screw
Helmet strap mount Bicycle handle bar mount
N
L
XTC-100 Action Camera
Thank you for your purchase of the XTC-100 Action Camera. As someone who seeks adventure, we are proud to
offer you the ultimate tool in capturing and recording your adventures. With easy to use one switch operation, 140
degree algle lens and 2 hour battery life you never miss a minute of the action. Once captured, simply connect to
your computer and upload the videos to share with friends. It is that simple! Enjoy!
What’s in the box
› Midland XTC-100 Action camera
› 2 GB Micro SD card
› 2 AAA Alkalinebatteries
› USB cable
› Goggle mount
› Helmet adhesive mount
› Dual Track mount for goggle mount and helmet adhesive mount.
› Helmet strap mount
› Bicycle handlebar mount
XTC-100 Features and Controls
Features:
› 640x480 resolution (4:3 aspect ratio)
› Records as AVI
› 30 frames per second
› 140 degree angle lens
Quick Start Guide
1. Open battery door and install batteries observing polarity. Replace battery cover.
2. Open and fold down back rubber cover. Insert micro Sd card observing proper direction. Close cover.
3. Move RECORD switch forward, recording will start in 8 seconds.
4. To stop recording, slide switch back to the off position.
5. Plug in camera to computer and download video.
Getting to Know the XTC-100
Batteries
1. To insert the batteries, push down the battery door latch on the right side of
the camera. Door will release. Push forward to remove.
2. Install 2 AAA batteries observing polarity.
3. Return battery door and click into place.
Battery Status Indicator Meaning
Solid Green Indicates full battery life
Solid Red Indicates half battery life
Blinking Red* Indicates low battery life
No Light Batteries are dead
Note: When the red battery LED begins blinking, be prepared to change the batteries because the camera will stop
recording at this point.
Micro SD Card
1. Open and fold down the back rubber cover.
2. Insert Micro SD card into slot observing proper direction (shown sideways).
3. Return rubber flap into place.
Recording
1. Move the RECORD switch forward. This turns the camera on.
2. The battery indicator will light from red to green. The SD card indicator will light green. The record indicator will begin
flashing red after 8 seconds. This indicates the camera is capturing video.
3. To stop recording, move the RECORD switch back to the off position.
Note: The camera will continue recording for 3 seconds after toggling the switch to the off position.
SD card LED Status Meaning
Green 1 GB or more avai lable
Orange 512 MB to1 GB available
Red Below 512 MB available or no MicroSD card installed.
Flashing Red Cannot read the card
Flashing Green Indicates card has been reformatted.
Memory Size Record Time
512 MB 7.5 Minutes
1 GB 15 Minutes
2 GB 30 Minutes
4 GB 60 Minutes
8 GB 120 Minutes
16 GB 240 Minutes
32 GB 480 Minutes
Note: The camera automatically splits the video into 2 GB segments.
Camera Mounting
Mount on Dual Track System
The XTC-100 was innovatively designed with an identi-
cal dual track mount system on either side of the came-
ra. This allows an ease of installation.
To mount the camera on the dual track mount, slide the
camera onto the dual track system with the two notches
on the mount facing towards the back of the camera.
To detach the camera from the dual track mount, hold
the camera with the lens facing away from you. Press
down the mount release switch and pull the mount to-
wards yourself.
The dual track mount allows the camera to be easily
mounted on both helmet mount and goggle mount. This
elimi nates the hassle of having to remount the camera
every time.
When mounting the camera on the dual track mount, you
must do the following:
1. Consider what you would like to shoot and use the
helmet mount or goggle mount accordingly.
2. Ensure, once attached, that the camera is aimed
straight and not towards the ground or at the sky.
Mount using the Thread Mount
On the bottom of the XTC-100 is a standard thread
mount that allows the camera to be mounted to an hel-
met strap mount or to a bicycle handlebar mount.
To fix the camera, insert the screw on the mount into
the camera thread and rotate the camera clockwise to
tighten down onto the screw.
When mounting the camera on the handlebars of a
bike or with the vented helmet strap mount follow these
steps:
1. Consider what you would like to shoot and mount
accordingly.
2. Ensure, once attached, that the camera is aimed
straight and not towards the ground or at the sky.
Compatible Systems
The XTC-100 can be used on both Windows operating system and MAC.
The camera records as AVI.
Downloading Videos
There is no need to install any software with the XTC-100. It is a plug and play device.
Ensure batteries are new or fully charged before downloading video.
Connect the camera to the USB port using the included cable.
The camera will be automatically recognized as external hard drive (USB key)
All your videos will be saved into the DCIM folder.
Reformatting the Micro SD card
The Micro SD card can be reformatted while in the camera. This allows you to delete all the videos at one time. Follow
these steps:
1. Move the RECORD switch to the record position.
2. When the battery indicator turns green, press and hold the Micro SD card reformat button.
3. Keep the Micro SD card reformat button down until the record indicator turns off and the SD card indicator begins
blinking green.
4. Move the RECORD switch to the off position.
Note: The camera cannot reformat the Micro SD card if the low battery light is on. Ensure new batteries are instal-
led in the camera before attempting the reformat process.
Tips and Tricks
Problem Solution
Batteries
Camera not turning on Ensure the batteries are installed properly observing polarity.
Make sure batteries are new or fully charged.
Recording
Camera not recording Make sure the switch is pushed all the way forward. If the record LED does not
come on, turn off the device and reinstall the batteries.
Verify available memory.
Micro SD card
Micro SD card not reading Ensure the Micro SD card is inserted properly.
Plug camera into the computer to verify it has available storage.
Attempt formatting process.
Video Playback
Slow or choppy video Verify the camera is plugged into a USB 2.0 device.
Remove other unused USB devices.
Transfer video to computer before viewing.
Video Downloading
Slow data transfer Verify the camera is plugged into a USB 2.0 device. If registering as 1.1, unplug and
the re-plug the device.
Remove other unused USB devices.
Computer does notrecognize ca-
mera
Ensure record switch is in the record position while connected to computer.
Ensure the Micro SD card is inserted properly.
Micro SD card may becorrupted. Attempt formatting process.
Sound
Excessive Wind Noise Place piece of tape over microphone hole.
Limited Warranty
Midland Radio Corporation will repair or replace, at its option without charge, any Midland XTC-100 Action camera
which fails due to a defect in material or workmanship within TWO Years following the initial consumer purchase.
This warranty does not apply to accidents of any kind, exposure to pressure, extreme temperatures (outside of -10°C to
45°C), and submersion water damage as this product is water resistant but not waterproof, battery leak or abuse.
Accessories have a 90 day warranty from date of purchase, inclu ding any mounts and cables. This warranty does not
include the cost of labor for removal or re-installation of the product in a vehicle or other mounting.
Hereby, CTE International declares that this XTC-100 is in compliance with the essential requirements and other rele-
vant provisions the Electromagnetic Compatibility Directive 2004/108/CE. A copy of Declaration of Conformity can be
found at: www.midlandradio.eu
140° degree glass lens
Microphone
Dual track mounting system
Record switch
forward: on/record
Record led
flashes red when
camera is recording
Battery led
Record switch
backward: Off/Stop recording
SD Card led
Mini USB connector
SD Card
reformat button
Mini SD Card slot
dual track system mount
Release button
Helmet adhesive mount Goggle mount
Camera thread Mounting screw
Helmet strap mount Bicycle handle bar mount
R U
XTC-100 Action Camera
Благодарим Вас за приобретение видеокамеры XTC-100, которая позволит любителям острых ощущений
делать видеозаписи своих приключений. Простота в использовании, широкий угол обзора, 2 часа в режиме
записи гарантируют то, что вы не пропустите ни одной секунды, наполненной адреналином.
Сделав запись, подключите камеру к компьютеру, загрузите видеоролик в Интернет и разделите свои
эмоции с друзьями!
Комплектация:
› видеокамера XTC-100 Action Camera
› карта памяти SD (емкость 2 Гб)
› 2 щелочные батарейки типа ААА
› кабель USB
› крепеж на очки
› крепеж на шлем на липучке
› крепеж на шлем на ремешке
› крепеж на руль велосипеда/мотоцикла
› держатель для установки видеокамеры на шлем или очки
Характеристики видеокамеры и элементы управления
Характеристики:
› разрешение 640х480 (размер кадра 4:3)
› формат записи: AVI (30 кадров в секунду)
› угол обзора 140°
Краткое руководство по использованию видеокамеры
1. Откройте крышку батарейного отсека и установите батарейки, соблюдая полярность.
Закройте крышку батарейного отсека.
2. Откройте резиновую крышку отсека карты памяти и установите карту памяти.
Закройте крышку отсека карты памяти.
3. Установите ползунок записи (Rec) в верхней позиции – запись начнется через 8 секунд.
4. Для остановки записи переместите ползунок (Rec) в нижнюю позицию (off).
5. Подключите камеру к персональному компьютеру и скопируйте видеоролик.
Установка батареек
1. Отсек для батареек расположен с правой стороны камеры. Нажмите
на фиксатор батарейного отсека и сдвиньте крышку в сторону объектива –
теперь можно ее снять.
2. Установите 2 батарейки типа ААА, соблюдая полярность.
3. Установите крышку батарейного отсека (при правильной установке,
вы услышите щелчок).
Индикация уровня разряда батареек
Индикатор разряда батареи Соответствующее значение
Постоянно горит зеленым светом Полный заряд батареи
Постоянно горит красным светом Батарея наполовину разряжена
Мигает красным светом* Низкий уровень заряда батареи
Не горит Батарея разряжена
*Внимание: когда индикатор начинает мигать красным светом, камера прекращает запись ролика.
В этот момент необходимо произвести замену батареек.
Установка Micro SD карты памяти
1. Откройте отсек карты памяти, расположенный на задней поверхности видеокамеры.
2. Установите карту памяти.
3. Закройте крышку отсека.
Запись ролика
1. Для включения видеокамеры переместите ползунок записи (Rec) ближе к объективу до щелчка.
2. Индикатор разряда батареи загорится зеленым или красным светом. Через 8 секунд индикатор записи (Rec)
начнет мигать красным светом – осуществляется запись ролика.
3. Для остановки записи переместите ползунок (Rec) ближе к USB разъему и разъему для установки Micro SD карты:
камера остановит запись через 3 секунды.
Индикатор состояния Micro SD карты Свободный объем памяти
Горит зеленым светом ≥ 1Гб
Горит оранжевым светом 512 Мб – 1Гб
Горит красным светом < 512 Мб или карта не установлена
Мигает красным светом Карта не читается
Мигает зеленым светом Карта была отформатирована
Объем памяти Доступное время записи (в мин.)
512 Мб 7,5
1 Гб 15
2 Гб 30
4 Гб 60
8 Гб 120
16 Гб 240
32 Гб 480
Внимание: видеокамера автоматически разделяет запись на фрагменты размером 2 Гб.
Установка видеокамеры
В комплекте вы найдете следующие варианты крепежей
видеокамеры, характеризующиеся различным назначением
и вариантами соединения с видеокамерой:
1. 2 крепежа на шлем:
на липучке – соединение с камерой осуществляется
посредством держателя (см. следующий раздел),
на ремешке – винтовая система соединения с камерой;
2. крепеж на очки – соединение с камерой
осуществляется посредством держателя
(см. следующий раздел);
3. крепеж на руль мотоцикла / велосипеда – винтовая
система соединения с камерой.
Держатель для установки видеокамеры
на шлем или очки
Данный держатель предназначен для фиксации видеокамеры на крепеже шлема или очков, позволяет быстро
и просто сменить положение видеокамеры (шлем-очки) в зависимости от цели / объекта съемки.
Для установки видеокамеры на держателе вставьте направляющие выступы видеокамеры в соответствующие
бороздки держателя и плавно двигайте камеру вдоль бороздок.
Теперь достаточно зафиксировать держатель с камерой на крепеже шлема (на липучке) или очков в необходимой
позиции (направлении), учитывая объект предстоящей съемки, и удостовериться, что объектив видеокамеры
направлен строго вперед, а не на землю или небо. Камера готова к использованию!
Для отсоединения видеокамеры от крепежа, зафиксируйте видеокамеру в руке (объектив направлен от вас),
нажмите на рычажок (см. рисунок сверху) и тяните держатель на себя.
Винтовая система соединения камеры с крепежом
Крепеж на шлем (на ремешке) и рулевой крепеж
имеют винтовую систему соединения видеокамеры
с крепежом.
Для фиксации видеокамеры на данном крепеже вставьте
винт крепежа в резьбовое соединение видеокамеры,
расположенное на нижней поверхности ее корпуса,
и вращайте видеокамеру по часовой стрелке.
Установите видеокамеру в необходимом направлении,
учитывая объект предстоящей съемки, и удостоверьтесь,
что объектив видеокамеры направлен строго вперед, а не
на землю или небо. Камера готова к использованию!
Совместимость видеокамеры с операционными системами персонального компьютера
Видеокамера совместима с операционной системой Windows и MAC.
Видеозаписи сохраняются в формате AVI.
Загрузка видеозаписей на персональный компьютер
Для загрузки видеоролика на персональный компьютер (ПК) установка какой-либо программы не требуется. Перед
началом загрузки удостоверьтесь, что батареи видеокамеры полностью заряжены. Подключите видеокамеру
к персональному компьютеру через разъем USB посредством кабеля, поставляемого в комплекте.
Персональный компьютер автоматически распознает внешнее USB устройство.
Все видеоролики сохраняются в папке DCIM.
Форматирование Micro SD карты памяти
Форматируя Micro SD карту памяти, вы можете просто и быстро удалить все видеозаписи.
Для этого:
1. Переместите ползунок записи (Rec) в верхнюю позицию (позиция записи).
2. Когда индикатор батареи загорится зеленым светом, нажмите и удерживайте кнопку форматирования карты
памяти.
3. Когда процесс форматирования карты завершится, индикатор записи (Rec) погаснет, а индикатор карты
памяти начнет мигать зеленым светом.
4. Переместите ползунок записи в нижнюю позицию (off).
Внимание: в случае, если горит индикатор низкого заряда батареи, невозможно осуществить
форматирование карты памяти. Таким образом, перед началом форматирования удостоверьтесь, что
батареи видеокамеры полностью заряжены.
Проблемы и неполадки
Проблема Решение
Батарейки
Камера не включается Проверьте, правильно ли установлены батарейки (соблюдена ли полярность).
Удостоверьтесь, что батарейки полностью заряжены.
Запись
Камера не осуществляет запись Удостоверьтесь, что ползунок записи расположен в верхней позиции
(до щелчка). Если индикатор записи не загорается, то выключите камеру
и переустановите батарейки.
Проверьте объем доступной памяти.
Карта памяти Micro SD
Карта памяти не читается Удостоверьтесь, что карта памяти установлена должным образом.
Посредством ПК проверьте доступный объем памяти.
Отформатируйте карту памяти.
Просмотр записи
Медленное или прерывистое
воспроизведение видео файла
Удостоверьтесь, что камера подключена к устройству, поддерживающему
USB 2.0.
Отсоедините другие USB устройства от ПК.
Перед просмотром записи сохраните её на ПК.
Загрузка видео файла на ПК
Медленная передача данных Удостоверьтесь, что камера подключена к устройству, поддерживающему
USB 2.0. Если камера регистрируется как устройство USB 1.1, то отсоедините
камеру и снова подключите к ПК.
Отсоедините другие USB устройства от ПК.
Персональный компьютер
не распознает камеру, как
внешнее USB устройство
Удостоверьтесь, что ползунок записи видеокамеры расположен в верхней
позиции (позиция записи).
Удостоверьтесь, что карта памяти установлена должным образом.
Отформатируйте карту памяти.
Звук
Чрезмерный шум, задувание
ветра
Прикройте отверстие микрофона.
Правила эксплуатации и ухода.
! Не пользуйтесь содержащими алкоголь жидкостями и чистящими средствами для очистки видеокамеры.
! Не погружайте видеокамеру в воду.
! Протирайте видеокамеру мягким влажным кусочком ткани.
! На время длительного хранения выключите видеокамеру и удалите из нее батарейки.
Внимание! Не вскрывайте корпус видеокамеры самостоятельно!
Несанкционированное вскрытие изделия лишит вас гарантии на устройство!
Гарантия
На данный товар гарантия выдается сроком на один год, считая со дня приобретения товара. Гарантийное
обслуживание осуществляется только при условии строгого соблюдения правил эксплуатации и требований
безопасности, указанных в руководстве пользователя.
Произведено или импортировано:
СТЕ Интернешнл с.р.л. Ул. Р. Севарди 7- 42010
Манкасаль, Реджио Эмилия, Италия
Импортер в России: ЗАО «Алан-Связь»
Интернет-сайт: www.midland.ru
105187, г. Москва, Фортунатовская, 31А, стр. 2 угол обзора 140°
микрофон
направляющие крепления камеры на держателе
ползунок записи (Rec)
в верхней позиции – включение камеры/
запись ролика
индикатор записи (Rec)
– мигает красным светом во время записи ролика
индикатор батареи
ползунок записи (Rec)
в нижней позиции – остановка записи/
выключение камеры
индикатор карты памяти
Mini USB разъем
кнопка форматирования карты памяти
отсек Mini SD карты памяти
бороздки держателя
рычажок
крепеж на шлем (на липучке) крепеж на очки
резьбовое
соединение
винт крепежа
крепеж на шлем (на ремешке) крепеж на руль