Candy FP 825 X AUS - Manual (Page 11)

• Press and hold the END
button
• Press the buttons
to set the time at which you
wish the oven to switch off
• Release the buttons
• Set the cooking function
with the oven function
selector
USING THE MINUTE TIMER
To set the cooking time, turn dial one
complete revolution and then position
the index to the required time. When
the time has lapsed, the signal will ring
for a few seconds.
USING THE END OF COOKING TIMER
This control enables to set the desired
cooking time (max. 120 min.) the oven
will automatically switch off at the end
of the set time.
The timer will count down from the set
time return to the O position and switch
off automatically.
For normal use of oven set the timer to
the position.
To set the oven ensure the timer is not on the O position.
To set the time, pull the lower control knob and rotate to position at the correct time.
To set as minute minder, set the cooking time by turning the top knob until the desired
time is shown on the small window on the left of the clock (max. 180 minutes).
When the preset time is elapsed the alarm will ring and the oven must be then switched
off manually. To stop the alarm set the cooking time to 0.
Lenght of
cooking chosen
Minute minder selector
control
Time selector control
USE OF THE ELECTRONIC PROGRAMMER
• Press and hold the
button
• Press the buttons or
to set the required time
• Release all the buttons
FUNCTION HOW TO ACTIVATE IT HOW TO SWITCH IT OFF WHAT IT DOES WHAT IT IS FOR
MINUTE MINDER
• Allows to use the oven as
alarm clock (could be
activated either with
operating the oven or
with out operating the
oven)
• When the set time as
elapsed an audible alarm
is activated (this alarm will
stop on its own, however
it can be stopped
immediately by pressing
the button)
• Sounds an alarm at the
end of the set time.
• To check how long is
left to run press the
button
• For cooking the desired
recipes
MANUAL
FUNCTION
• Turn the oven function
selector to position O.
• Enables you to operate
the oven.
COOKING
TIME
• Press and hold the
TIMER button
• Press the buttons or
to set the lenght of coo-
king required
• Release all buttons
• Set the cooking function with
the oven function selector
• When the time is elapsed
the oven will switch off
automatically. Should you
wish to stop cooking
earlier either turn the
function selector to 0, or
set time to 0:00
(TIMER and buttons)
• It allows to preset the
cooking time required
for the recipe chosen
• To check how long is
left to run press the
TIMER button.
• To alter/change the
preset time press
TIMER and buttons
• At the end of the
cooking set time,
the oven will switch
off automatically and an
audible alarm will ring.
END OF
COOKING
• This function is typically
used with “cooking time”
function. For example
if the dish has to be cooked
for 45 minutes and needs
to be ready by 12:30,
simply select the required
function, set the cooking
time to 45 minutes and the
end of cooking time to
12:30.
• Cooking will start automa-
tically at 11:45 (12:30
minus 45 mins) and will
continue until the pre-set
end-of-cooking-time, when
the oven will switch itself
off automatically.
WARNING.
If the END of cooking is
selected without setting
the length of cooking time,
the oven will start cooking
immediately and it will
s t o p a t t h e E N D o f
cooking time set.
• At the time set, the oven
will switch off. To switch
off manually, turn the
oven function selector
to position O.
• Enables you to set the
end of cooking time
• To check the preset
time press the END
button
• To modify the preset
time press buttons
END +
• Press the button
• Set the cooking function
with the oven function
selector
10 GB
WARNING : the first operation to carry out after the oven has been
installed or following the interruption of power supply (this
is recognizable the display pulsating and showing )
is setting the correct time. This is achieved as follows
• Press and hold the Timer and END buttons
• Set time with buttons
• Release all buttons
ATTENTION the oven only operates if set on manual function or preset time.
N.B.: on some models the symbols are replaced by + and - .
SETTING THE CORRECT TIME