Candy LSC DE701TNORD - Manual (Page 21)

41
Interrupting a programme
It is not recommended that the door be opened while a programme is
running, and especially not during the main wash phase and final drying.
However, the appliance will stop automatically when the door is opened.
At this point the various wash options can be programmed or cancelled.
The current programme can also be cancelled.
If, the door is opened during a programme, the symbol for that programme
will flash in the display and the machine stops.
Please Note:
If you open the door during the drying cycle an audible audio signal
advises you that the drying cycle has not yet completed.
To restart the machine, press the "START" button and the time remaining
for the programme will flash. Now close the door.
If you wish to cancel or change a programme that is running, carry
out the following:
keep the "START" button pressed in until the number of the
programme stops flashing. A new programme can now be set.
NB: If, on pressing the "START" button the symbol "00" starts to flash on
the display, it means that there is water in the machine.
Then release the "START" button and the machine will automatically
empty the water; wait for the audible signal, after which the new
programme can be set.
Before starting a new programme, you should check that there is still
detergent in the dispenser. If necessary, top up the dispenser.
End of programme
The end of the programme is indicated by an audible signal (if it has not
been deactivated). The number of the programme that has just finished will
appear on the display.
Important:
If the programme shown in the display starts to flash and the machine
will not let any more programmes be selected, press the ''START''
button and keep this button pressed until the display stops flashing.
Delay Start programme button
To set the delay start programme press the button.
On the first press the current setting appears on the display. Each time the
button is pressed the delayed time in one hour increments increases, up
to a maximum of 19 hours.
Once set, wait until the selected time is confirmed when it appears in the
display. Press the "START" button to start the countdown. If the
countdown has not already been activated, the delay start can be
cancelled by pressing the button until the selected programme
appears on the display.
The delay start can be cancelled at any time simply by keeping the
"START" button pressed in until the required wash cycle appears on the
display.
If you wish to see which programme has been selected, press the
"Programme Selection Button” .
NB: If the door is opened during the countdown, for example to select one
of the options (or to add more dishes), the "START" button should be
pressed before closing the door again, in order to restart the countdown.
Pr
40
Attention
This dishwasher is equipped with an anti-overflow safety device which
works even when power is off, and if the water level is too high, the
supply will automatically be closed off.
Important
To ensure the correct operation of the anti-overflow safety device, it is
recommended not to move or to tilt the dishwasher during operation.
if it is necessary to move or to tilt the dishwasher, first make sure the
washing cycle is finished and that no water is left in the tank.
Setting a programme
Press the button; the last programme selected will appear on the
display.
To set a new programme, press the “Programme Selection Button”
"P" .
When the required programme is shown in the display, press the
"START" button. The time of the selected programme (in hours and
minutes) will start to flash in the display.
After an audible signal has sounded (if it has not been deactivated) the
programme will start automatically.
Half load button
By pressing this button it is possible to wash a small quantity of
crockery using only the upper basket for dishes and cutlery in the
bottom basket.
This reduces water and energy consumption and requires a smaller
quantity of detergent.
Please Note:
When the ''START'' button has been selected it is not possible to
deselect it.
“Extra rinse” button
Extra rinse for very dirty washing.
Economy button
The "E" button reduces the final heating of the water during the last
rinse. This activates a natural drying process, as with a normal draining
board, simply by leaving the door ajar at the end of the cycle to enable
the natural circulation of air. The "E" button permits an energy saving
of more than 20% and shortens the cycle.
Recommended for evening washes when the dishes are not required
perfectly dry, immediately, straight after washing.
Selecting the programme and special functions
Use in conjunction with programme guide
Pr
I