Activeforever DL930 Day Light by Uplift Technologies - Manual (Page 5)

Why Day-Light Sky?
• Clinically proven technology
• Developed with BrightZone™ Technology
• Light therapy system and versatile task lamp
• Designed for home or office
BrightZone™ Technology
Engineered and tested to provide the appropriate
field of illumination and 10,000 LUX experts
recommend for maximum therapeutic benefit.
Bright Light Therapy Standards
The Center for Environmental Therapeutics, a not-
for-profit professional organization, has specified
criteria for light box selection to ensure user safety
and effective treatment. Day-Light Sky was
designed to meet these standards.
Bright Light
Therapy Standards
• Design based on university
clinical trials
• 10,000 LUX outdoor level at
a comfortable distance
• Emits balanced white light for
eye safety
• Broad field of illumination for
easy use
• 99.3% UV filtered protection
• Glare-free diffuser for
visual comfort
• Adjustable height for
optimal positioning
• Projects light from above
for best effect
Day-Light Sky
Visit www.cet.org for detailed information on users’ experience
and extensive guidance from leading doctors.
Adjusting Light Angle and Height
For optimum light therapy usage, you will need to
adjust your Day-Light Sky so that:
• The light shines down at an angle of about 15°; and
• Your eyes are approximately in the center of the light.
To Adjust the Angle and Height of the Light
There are two adjustment buttons on the arm of your
Day-Light Sky. Each silver button, when pressed,
allows you to move the light head or arm to several
different positions.
When you wish to adjust the height or angle of the light
head, press the appropriate adjustment button while
holding the light head to move it to desired position.
To maintain the position, release the adjustment button
to lock the arm in position.
By removing your hand from the light head and
allowing it to engage, the head will properly and gently
settle to the engaged position.
To set the angle of the light at approximately 15° use the
best combination of adjustments based on where your
Day-Light Sky is positioned and your height.
When not using your Day-Light Sky for light therapy, you
can easily reposition the light head to use as a task lamp
over or near your work space.
Sky
To Install a Light Tube
1. To reinstall the light tube, hold the tube horizontally
and slide the top end into the retainer clip.
2. Next, gently slide the prongs into the light socket.
When it is fully in place you will hear a ‘click’.
3. Once the light tubes are installed correctly, plug the
Day-Light Sky in and check that the lights illuminate
in each switch position. If working, unplug and
continue to the next step. (If not, try reinstalling
the tubes again to determine if there may be a
problem with the light.)
4. Replace the plastic lens by sliding the front under
the retention clips on the lamp head housing. It
should clip easily back into place.
5. Reinstall the four (4) screws ensuring they pass
through the lens. Do not over tighten as this could
result in stripping the screws.
Using and Adjusting the Light
Intensity Settings
The Day-Light Sky operates with two 55 watt compact
fluorescent light tubes. There are two light intensity
settings on your new Day-Light Sky – a high intensity
and low intensity setting. High intensity is the recom-
mended dosage for light therapy sessions, while low
intensity may be preferred for use as a task light.
High Intensity Setting—Light Therapy
At this setting, the Day-Light Sky emits 10,000 LUX light
intensity when sitting a distance of 11 inches (28 cm)
from the light. This light level is the recommended
dosage for 20-30 minute daily light therapy sessions.
Push the switch to the side with solid yellow dot
marking. Both light tubes will be on at this setting.
Low Intensity Setting – Task or Ambient Lighting
You may prefer the lower intensity setting when using
your Day-Light Sky for work or ambient lighting – it’s
your choice. The lower setting emits a light intensity of
5,000 LUX when sitting 11 inches (28 cm) from the light.
As this is still quite bright, we recommend that you
either move your Day-Light Sky further away, or angle
the light down over your work area when using it for
non-light therapy uses.
For the lower light intensity setting, push the switch to
the side with the yellow “O”. You should see only one of
the light tubes illuminate.
Assembling your Day-Light Sky
The base plate ensures your Day-Light Sky will stand in a
stable position.
4. Carefully lift the assembled unit and stand it upright.
5. Turn the light head counter clockwise 90° for
therapeutic or task lighting.
Fr
on
t
Lay your Day-Light
Sky in the packing
position with the
lens facing upward.
Position your
Day-Light Sky base
into the recessed
groove on the base
plate with the front
of the base plate
facing forward. Align
the hole in the base
with the hole in the
Day-Light Sky.
Using the
included Philips #2
screwdriver, insert
and tighten the
single Philips screw
securely into the
light base. Do not
over tighten.
1.
2.
3.
4 5
Sky
Adjustable button