Acura Embedded AcuBrite 15″ - Manual (Page 10)

AcuBrite™ Manual User’s Manual
ACURA INS
The following instruction is desi
installing Acura products and make
experience will aid in the installa
installation of any electrical or me
equipment as well as any instru
made available prior to beginning
The installer is required to prepare
mechanical needs of the project
interference are addressed. A rev
needs to be checked off and a c
Customer file. All projects requir
limited.
stallation
ss of
of the project.
Please refer to caution and insta
component or accessory.
In order to receive the best perfo
should be installed in a way that
ating c
eck
opera
staller
possible. Follow up with a Corr
ts or con
All parts, components and accessories a e received and prepared for installation
Areas to receive equipment are clear and free from obstruction
The mounting system selected is r the apparatus.
Before attaching brackets make sure there are no hidden fluid or wiring obstructions
attaching any wiring be sure that power leads are correctly fused and correctly
will void
ly operate the unit
known
______
_
Page 16
TALLATION INSTRUCTIONS
gned to assist the technician or customer in the basic steps of
s the assumption that commonsense and previous
n. Safety and caution must always take precedence in the tio
chanical system. The correct tools, parts, fasteners, saf
ctions, diagrams and schematics must be gathered, revie
he process of installation.
in advance the w
ety
wed or
t
ork area and see that the electrical or
are in place before starting and that any other possible
iew of the Installation Check List is critical since this list
y sent back to the supplier so it can be atta op ched to the
e the filling out of appropriate forms or else warranty may be
structions are not designed to be ex The list and/or these In
they are part of a proce In haustive or restrictive
total quality management and will help the installer to be in control
llation guides provided with each piece of equipment,
ance out of a new Acura computer system all components
ows for ease of operation by customer’s trained personnel o
ditions.
rm
all r
on
off the following boxes so the undersigned can verify that the
onal. If something is not working as initially configured and
mediately so that the problem can be fixed as promptly as
e Action Report (CAR) where appropriate.
trainer under regular oper
Please take a moment to ch
installation is complete and
tested please inform the in
ti
im
ectiv
ditions to watch out for: (Please initial them off as you Below are some poin
proceed)
r
appropriate fo
Use appropriate fasteners and backing as required.
Ensure Power Sources are identified and adequate to operate system without over
taxing available battery reserve. An Amp hour survey should be completed and
additional battery capacity addressed. Power is direct from battery to a distribution
fused block.
Page 15
Before
identified (
+ or –) as well as correct voltage and wire size (12 ga power supply
minimum) Caution: Incorrect connection of wires will affect the electronics and
warranty – (Burnt wiring and blown circuitry is evidence of improper installation)
Fasteners will require lock washers, washers, isolation or proper grounding
Computer is adequately hidden and out of the way yet readily accessible with good
ventilation.
ouch screen is mounted securely to the apparatus. T
Touch screen is in a location where desired user/s can comfortab
Unit is fully functional while the engine or radio of the apparatus is running and free of
RF
Connections, components or accessories are no imp t eding the duties of personnel
Factory operating system (locked) and all factory applications are functional
All service personnel and trainers understand the components and wiring for all
applicable systems as well as In-line fuses are accessible and their locations are
Administrative controls for systems are in the hands of trained service personnel
Note: Check twice install once.
sistance call your sales and service representative first for guidance. For As
_________ ___________________________
__________
Print Name Signature of Chief or Representative Date of sig nature
_________ __________________________ _______________
Print Name Signature of Authorized Installer Date of signature