Longacre Computerscales Wireless Accuset II - Manual

Shows Low Batt
Change Soon
on display when batteries needs
replacement (at this point you still have
approximately 2 hours of run time).
Power consumption is so low that it
should not be necessary to replace
more than once per season.
• ‘AA’ battery access is on the bottom
of the control box. Remove lid and
replace with 6 quality AA Alkaline.
BE SURE THE POLARITY IS CORRECT.
Coil spring goes to negative end of batt.
See “There are electronics in the pads”
to the right for pad battery instructions.
Zero:
Push BEFORE putting car on
scales.
DON'T push Zero AFTER car
is on scales.
If you do accidentally push Zero
remove car from scales and re-zero.
Wheel Weights &
Partial % Displays
These 2 buttons let you show either 4
wheel weights and cross - OR - all
partial weights and %. You can go back
and forth as needed. Do NOT reZero.
On/Off:
Turn on before putting car on
scales. Allow to warm up for
a minute or so.
Longacre Racing Products, Inc.
16892 146 th St SE, Monroe, Wa. 98272
(360) 453 2030
www.longacreracing.com
LF 590 720 RF
LR 685 772 RR
Cross 1546 57.26%
LF 590 720 RF
LR 685 772 RR
TOTAL 2806
Cross 1546 57.26%
1/13
NOTE: If service is ever needed please call factory first. You may be able to send back just part
of the system, saving freight.
LEFT 1436 51.24%
REAR 1531 53.13%
CROSS 1649 57.77%
TOTAL 2806 BITE 157
LEFT 1436 51.23%
RIGHT 1436 51.23%
FRONT 1531 53.61%
REAR 1531 53.19%
OR OR
Instructions for Wireless AccuSet II
1) Set up pads along side car. Scale pads are marked RF, LR, etc. and MUST be used in this location.
2) Turn on the pads - see the orange rocker switch. The LED will flash green. Turn on control box. After 10-15 seconds the pads will link and weights will show.
3) Push Zero.
This defines "0" weight. DON'T PUSH ‘ZERO’ AFTER CAR IS ON SCALES. Low batteries in pads are indicated by the LED showing red.
4) Lift car and place pads under wheels. For more consistant cross weights "shake" car up & down at each corner to settle out any shock or suspension friction.
5) System shuts down after 90 minutes to extend battery life. If needed simply turn back on. DO NOT RE-ZERO unless car is off scales.
There are 2 different displays for both
Wheel Weights and Partial % . See
examples at the right. If you want the other
one push the Wheel Weights or Partial
% button and hold for 3 seconds and
release (beeps). That display will change
and will stay until you change it again.
NOTE: “Bite” is LR minus RR.
Base Line Recall
This is a 1 slot memory storage for
comparison. To access just push the
“ Base Line Recall ” button.
To store push Wheel Weights and Base
Line Recall buttons at the same time
and hold for 3 sec.
Convert to Metric:
Go to Partial %
mode and hold
that button 6 sec-
onds (beeps)
There are electronics
in the pads.
Please treat the pads
with the same care as
you do the control box.
• Keep the system clean and dry. Do
not drop either the pads or the control
box. Keep away from static electricity.
• Store in a clean dry place. Remove
batteries if scale will be stored unused
for more than 6 months
• A pad not transmitting or out of
range is indicated by “- - - -”
• Capacity/scale pad is 1500 lbs.
• Batteries in the pads are on the end
opposite the black wireless module.
Remove 2 screws from the bottom of
the pad & slide the battery holder out.
Remove the small screw and the lid.