Spicer Driveline Components Catalog - Companion Flanges - Manual (Page 10)

10
Important: See Safety Information in General Information Section (J300P-GI)
J300P-1
COMPANION FLANGES
Spline Hole
• Part is discontinued „ Part is available until supply is exhausted Ž Not sold separately
F
i
g
u
r
e
D C B Bolt Hole E F G Companion
Spline Pilot Brake Flange Flange Companion
Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub when listed) Number Number
2.541-19 Involute Spline
2.541 7.750-F 7.250 .440D 12 — 3.125 2.825 4.590 2 — — 6.5-1-3001ƒ
2.544-49 Involute Spline
2.544 7.750-F 7.250 .375D 8 — 3.818 2.125 3.130 1 131436K• 5008437 6-1-6281Ž 1710
Nut #131095 (incl. in assy) is used only on Spicer Axles.
Slinger not sold separately
2.544 7.750-F 7.250 .375D 8 — 3.818 2.125 3.130 1 131436K• 5008437 5008460•
Nut #131095 (incl. in assy) is used only on Spicer Axles.
Slinger not sold separately
2.544 7.750-F 7.250 .375D 8 — 3.818 2.125 3.130 1 5008460• 5008437 6-1-6281Ž 1710
2.560-20 Involute Spline
2.560 7.750-F 7.250 .438D 12 6.625 3.500 3.344 4.000 4 — — 6.5-1-2161 1810
2.625-25 Involute Spline
2.625 7.750-F 7.250 .375D 8 — 3.500 3.016 3.625 3 — — 6-1-5511 1710
2.635-20 Involute Spline
2.635 6.992-M 8.250 .625T 8 — 4.004 3.305 4.442 5 8-1-821X• 230888 8-1-811Ž
.560 deep counterbore at hub end
Slinger not sold separately
2.750-10 Spline
2.750 6.625-F 6.125 .375D 8 — 3.750 3.000 4.060 3 5-1-6611X• 231616 5-1-6601Ž
2.750 7.750-F 7.250 .438D 12 — 4.000 2.938 3.750 4 — — 6.5-1-1871ƒ 1810
Hub machined for speedometer gear
2.750 7.750-F 7.250 .438D 12 — 3.500 3.000 4.062 4 — — 6.5-1-741 1810
2.750 7.750-F 7.250 .438D 12 — 3.750 3.000 4.062 4 6.5-1-2361X 231616 6.5-1-2311• 1810
2.750 8.000-M 7.250 .375D 8 8.000 3.500 3.000 3.688 3 — — 6-1-2381ƒ 1710
Use with thru stop brake disc. mount between fl ange & yoke