Splined midship tube shafts, Companion flange or end yoke design – Spicer Driveline Components Catalog - Tube Shafts User Manual
Page 10
J300P-7
SPLINED MIDSHIP TUBE SHAFTS
Companion Flange or End Yoke Design
Style 1
Style 2
10
Important: See Safety Information in General Information Section (J300P-GI)
•
Part is discontinued
Part is available until supply is exhausted
Not sold separately
L
Length
of
Spline
K
End of Spline
Spline to
Point of Weld
Thread Size
S
t
y
l
e
Y
End of Spline
to Bearing
Shoulder
B
Shoulder
Diameter
G
Length of
Shoulder
Midship
Tube Shaft
Part Number
Tube
Dia.
Wall
Thickness
Fits Tube
1.750-34 Involute Spline
1.771 Bearing Diameter (C)
3.500 .095
3.188
5.050
2 2.060
1.250-18
2.153
.322
70-53-61
Spline has helix on tooth. End yokes will be a tight fi t.
3.500 .134
3.250
4.344
2 2.062
1.250-18
2.188
.812
5-53-261
Spline has helix on tooth. End yokes will be a tight fi t.
4.000 .095
3.189
4.327
2 2.059
1.250-18
2.154
—
100-53-31
Spline has helix on tooth. End yokes will be a tight fi t.
4.000 .095
3.250
4.344
2 2.125
1.250-18
2.188
.812
90-53-31
Spline has helix on tooth. End yokes will be a tight fi t.
4.000 .134
3.125
4.219
2 2.000
1.250-18
2.188
.812
90-53-11
Spline has helix on tooth. End yokes will be a tight fi t.
4.000 .134
3.250
4.344
2 2.125
1.250-18
2.188
.812
5-53-271
5-53-271 was replaced by 90-53-11
2.000 Bearing Diameter (C)
3.500 .134
5.625
7.125
2 2.062
1.250-18
2.500
.344
5-53-291
1.752-34 Involute Spline
1.772 Bearing Diameter (C)
4.000 .083
3.188
3.988
2 2.059
1.250-18
2.154
.559
70-53-31
1.950-38 Involute Spline
1.968 Bearing Diameter (C)
4.000 .134
4.060
5.150
2 2.840
1.250-18
2.440
.812
6-53-411
Spline has helix on tooth. End yokes will be a tight fi t.
4.330 .197
3.811
5.055
2 2.618 M30X2-6G
2.440
.811
140-53-11
4.562 .165
4.062
5.156
2 2.844
1.250-18
2.438
.812
6-53-421
Spline has helix on tooth. End yokes will be a tight fi t.
4.566 .157
3.346
4.591
2 2.125 M30X2-6G
2.441
.811
140-53-41•
4.567 .157
3.811
5.055
2 2.618 M30X2-6G
2.441
.811
140-53-31•
1.958-10 Spline
1.967 Bearing Diameter (C)
4.000 .134
3.000
4.438
2 1.938
1.250-18
2.625
1.062 6-53-211•
1.968 Bearing Diameter (C)
3.500 .156
4.062
5.156
2 3.000
1.250-18
2.438
.812
6-53-151•
4.000 .134
4.062
5.156
2 2.875
1.250-18
2.438
.812
6-53-201
4.500 .134
4.062
5.156
2 2.875
1.250-18
2.438
.812
6-53-241
1.983-31 Involute Spline
2.363 Bearing Diameter (C)
3.500 .134
4.484
7.406
2 2.141
.500-20
2.774
1.281 4-53-331•
2.437 Bearing Diameter (C)
3.500 .134
7.531
8.562
1 1.859 M12X1.750-6H —
4.719 4-53-501•
.268 key width in shoulder; Metric thread
2.000-10 Spline
2.165 Bearing Diameter (C)
4.000 .134
4.250
6.844
2 2.875
1.250-18
2.938
1.875 6-53-331
4.000 .134
4.562
7.875
2 2.625
1.250-18
2.562
2.938 6-53-261•