Veris Industries TC SERIES Install - Manual

Installation Guide
Temperature
Z205468-0D Page 1 of 2 ©2013 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 08131
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
TM
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classified locations.
• Read and understand the instructions before installing
this product.
• Turn off all power supplying equipment before working on it.
• The installer is responsible for conformance to all applicable codes.
No responsibility is assumed by Veris Industries for any consequences arising out of the
use of this material.
Product Identification
Product Overview
TC and TS ceiling mounted temperature sensors monitor the temperature of the air in a room. The design is ideal for
large open spaces, such as open office environments. The TC comes with a variable length temperature probe, and
the TS has a recessed design. Both models have resistive outputs compatible with building control systems. Both
models are warranted for a period of five years.
TC/TS Series
Ceiling Mounted Temperature Sensors
Specifications
Wiring 22 AWG; 2-wire RTD/Thermistor
Housing White ABS Plastic
(Black plastic available for TS, consult factory)
TC
TS
Sensor Type
TC
Probe Length
B = 4" (102mm)
C = 6" (152mm)
D = 8" (203mm)
E = 12" (305mm)
F = 18" (457mm)
G = 24" (610mm)
Cal Certificate
0 = None
1 = 1 point Cal validation
2 = 2 point Cal validation B = 100R platinum, RTD
C = 1k platinum, RTD
D = 10k T2, Thermistor
E = 2.2k, Thermistor
F = 3k, Thermistor
G = 10k CPC, Thermistor
H = 10k T3, Thermistor
J = 10k Dale, Thermistor
K = 10k w/11k shunt, Thermistor
M = 20k NTC, Thermistor
Sensor Type
TS
Cal Certificate
0 = None
1 = 1 point Cal validation
2 = 2 point Cal validation B = 100R platinum, RTD
C = 1k platinum, RTD
D = 10k T2, Thermistor
E = 2.2k, Thermistor
F = 3k, Thermistor
G = 10k CPC, Thermistor
H = 10k T3, Thermistor
I = 1k Balco (Nickel-iron) RTD
J = 10k Dale, Thermistor
K = 10k w/11k shunt, Thermistor
M = 20k NTC, Thermistor
N = 1800 ohm, Thermistor
R = 10k US, Thermistor
S = 10k 3A221, Thermistor
T = 100k, Thermistor
U = 20k “D”, Thermistor
W = 10k T2 high accuracy, Thermistor
Y = 10k T3 high accuracy, Thermistor
Z = 10k E1, Thermistor
CC = 15k, Thermistor
N = 1800 ohm, Thermistor
R = 10k US, Thermistor
S = 10k 3A221, Thermistor
T = 100k, Thermistor
U = 20k “D”, Thermistor
W = 10k T2 high accuracy, Thermistor
Y = 10k T3 high accuracy, Thermistor
Z = 10k E1, Thermistor
CC = 15k, Thermistor