Veris Industries H922030A Install - Manual

6%2)3 CURRENT MONITORING INSTALLATION GUIDE
Z204089-0C PAGE 1 ©2009 Veris Industries USA 800.354.8556 or 503.598.4564 / [email protected] 03095
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Split-Core Self-Powered Current Transducer,
30, 60, or 120 Amp, 0-5VDC Output
Installer’s Specifications
Amperage Range 0-30/60/120 Amps (fixed)
Sensor Power Induced from monitored conductor
Insulation Class 600VAC RMS
Frequency 50/60Hz
Temperature Range -15° to 60°C (5° to 140°F)
Humidity Range 10-90% RH non-condensing
Accuracy ±2% F.S. from 10% to 100% of selected range
Response Time less than 2 sec
Safety IEC 61010-1:2001 CAT III
For CE compliance, conductor shall be insulated according to IEC 61010-1:2001, Installation
Category III or equivalent.
PRoduct design provides for basic insulation only.
)";"3%
0'
&-&$53*$
4)0$,

&91-04*0/

03
"3$
'-"4)
t
'PMMPX
TBGF
FMFDUSJDBM
XPSL
QSBDUJDFT
4FF
/'1"
&
JO
UIF
64"

PS
BQQMJDBCMF
MPDBM
DPEFT
t
5IJT
FRVJQNFOU
NVTU
POMZ
CF
JOTUBMMFE
BOE
TFSWJDFE
CZ
RVBMJmFE
FMFDUSJDBM
QFSTPOOFM
t
3FBE

VOEFSTUBOE
BOE
GPMMPX
UIF
JOTUSVDUJPOT
CFGPSF
JOTUBMMJOH
UIJT
QSPEVDU
t
5VSO
Põ
BMM
QPXFS
TVQQMZJOH
FRVJQNFOU
CFGPSF
XPSLJOH
PO
PS
JOTJEF
UIF
FRVJQNFOU
t
6TF
B
QSPQFSMZ
SBUFE
WPMUBHF
TFOTJOH
EFWJDF
UP
DPOmSN
QPXFS
JT
Põ

%0
/05
%&1&/%
0/
5)*4
130%6$5
'03
70-5"(&
*/%*$"5*0/
t
0OMZ
JOTUBMM
UIJT
QSPEVDU
PO
JOTVMBUFE
DPOEVDUPST
'BJMVSF
UP
GPMMPX
UIFTF
JOTUSVDUJPOT
XJMM
SFTVMU
JO
EFBUI
PS
TFSJPVT
JOKVSZ
%"/(&3
Wiring ExamplE
H922xxxA 922xxxA
DimEnsions
/05*$&
t
5IJT
QSPEVDU
JT
OPU
JOUFOEFE
GPS
MJGF
PS
TBGFUZ
BQQMJDBUJPOT
t
%P
OPU
JOTUBMM
UIJT
QSPEVDU
JO
IB[BSEPVT
PS
DMBTTJmFE
MPDBUJPOT
t
5IF
JOTUBMMFS
JT
SFTQPOTJCMF
GPS
DPOGPSNBODF
UP
BMM
BQQMJDBCMF
DPEFT
t
.PVOU
UIJT
QSPEVDU
JOTJEF
B
TVJUBCMF
mSF
BOE
FMFDUSJDBM
FODMPTVSF
quick install
Disconnect and lock out power to the conductor being monitored. 1.
Install the removable mounting bracket to the back of the enclosure. 2.
Run the conductor through the current sensor window, and close the sensor until 3.
the clip snaps shut. For monitoring currents above or below the device’s range, see
the Notes section on page 2.
Connect the 0-5VDC self-powered output to the analog input of the control panel. 4.
Scale the control panel for 0-5VDC input. 5.
Fan or Pump
CONTROLLER
VERIS INDUSTRIES Portland, Oregon 97223 1-800-354-8556
CONTACTOR
MOTOR
Insulated Conductor
COMM
0-5 VDC
+
-