Veris Industries H600 Install - Manual

TM
CURRENT MONITORING INSTALLATION GUIDE
Z201983-0K PAGE 1 ©2013 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 03132
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Split-Core Current Switch,
Fixed Trip Point
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Read, understand and follow the instructions before installing this product.
• Turn off all power supplying equipment before working on or inside the equipment.
• Use a properly rated voltage sensing device to confirm power is off.
DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION
• Only install this product on insulated conductors.
Failure to follow these instructions will result in death or serious injury.
A qualified person is one who has skills and knowledge related to the construction and
operation of this electrical equipment and the installation, and has received safety
training to recognize and avoid the hazards involved. NEC2009 Article 100
No responsibility is assumed by Veris Industries for any consequences arising out of the
use of this material.
DANGER
WIRING EXAMPLE
TM
600
DIMENSIONS
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classified locations.
• The installer is responsible for conformance to all applicable codes.
• Mount this product inside a suitable fire and electrical enclosure.
Motor
Fan
DDC CONTROLLER
DI
CONTACTOR
Insulated Conductor ONLY
2.5" *
(64 mm)
2.1"
(54 mm)
3.5"
(89 mm)
2.9"
(74 mm)
0.4” x 0.2”
(10 mm x 5 mm)
Slot (2x)
1.2"
(31 mm)
Removable Mounting Bracket
0.7"
(18 mm)
0.5"
(13 mm)
2.1"
(54 mm)
1.0" *
(26 mm)
0.6"
(16 mm)
RoHS
Compliant
SPECIFICATIONS
Sensor Power Induced from monitored conductor
Amperage Range 0.15 to 200A Continuous
Status Output Ratings N.O. 1.0A@30VAC/DC not polarity sensitive
Insulation Class 600VAC RMS (UL), 300VAC RMS (CE)
Setpoint Fixed at 0.15 A max. (60 Hz)
Frequency 50/60 Hz
Temperature Range -15° to 40°C (5° to 104°F)
Humidity Range 10-90% RH non-condensing
Off State Resistance Open switch represents 1+ MΩ
On State Resistance Closed switch represents <200 mΩ
Terminal Block Wire Size 14 to 24 AWG (2.1 to 0.2 mm 2 )
Terminal Block Torque 3.5 to 4.5 in-lb (0.4 to 0.5 N-m)
Agency Approvals UL508, CE: EN61010-1
Installation Category Cat. III, pollution degree 2
For CE compliance, conductor shall be insulated according to IEC 61010‑1.
The product design provides for functional insulation only.
Listed for use with 75°C insulated conductors.
INSTALLATION
Disconnect and lock out power to the enclosure
containing the condustor to be monitored.
1. Locate a mounting surface for the removable mounting bracket that will allow the
monitored conductor to pass through the center window when it is installed and
that will keep the product at least ½” (13 mm) from any uninsulated conductors.
Determine cable routing for the controller connection, allowing wiring to reach
the mounting location.
2. Drill holes to mount the bracket to the chosen surface using the included screws.
3. Wire the output connections between the sensor and the controller (solid-state
contact).
4. Snap the sensor over the wire to be monitored clip the assembly to the mounting
bracket.
5. Secure the enclosure and reconnect power.