Veris Industries AH25 Install - Manual

6%2)3 Power Monitoring inStALLAtion gUiDe
Z205211-0B PAGE 1 ©2008 Veris Industries USA 800.354.8556 or 503.598.4564 / [email protected] 10082
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
AH24/AH25 AH24/AH25
Dimensions
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Read, understand and follow the instructions before installing this product.
• Turn off all power supplying equipment before working on or inside the equipment.
• Use a properly rated voltage sensing device to confirm power is off.
DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION
Failure to follow these instructions will result in death or serious injury.
DANGER
/05*$&
t
5IJT
QSPEVDU
JT
OPU
JOUFOEFE
GPS
MJGF
PS
TBGFUZ
BQQMJDBUJPOT
t
%P
OPU
JOTUBMM
UIJT
QSPEVDU
JO
IB[BSEPVT
PS
DMBTTJmFE
MPDBUJPOT
t
5IF
JOTUBMMFS
JT
SFTQPOTJCMF
GPS
DPOGPSNBODF
UP
BMM
BQQMJDBCMF
DPEFT
t
.PVOU
UIJT
QSPEVDU
JOTJEF
B
TVJUBCMF
mSF
BOE
FMFDUSJDBM
FODMPTVSF
'$$
1"35

*/'03."5*0/
/05&

5IJT
FRVJQNFOU
IBT
CFFO
UFTUFE
CZ
UIF
NBOVGBDUVSFS
BOE
GPVOE

UP
DPNQMZ
XJUI
UIF
MJNJUT
GPS
B
DMBTT
"
EJHJUBM
EFWJDF

QVSTVBOU
UP
QBSU


PG
UIF
'$$
3VMFT
5IFTF
MJNJUT
BSF
EFTJHOFE
UP
QSPWJEF
SFBTPOBCMF

QSPUFDUJPO
BHBJOTU
IBSNGVM
JOUFSGFSFODF
XIFO
UIF
FRVJQNFOU
JT

PQFSBUFE
JO
B
DPNNFSDJBM
FOWJSPONFOU
5IJT
FRVJQNFOU
HFOFSBUFT


VTFT

BOE
DBO
SBEJBUF
SBEJP
GSFRVFODZ
FOFSHZ
BOE

JG
OPU
JOTUBMMFE
BOE

VTFE
JO
BDDPSEBODF
XJUI
UIF
JOTUSVDUJPO
NBOVBM

NBZ
DBVTF
IBSNGVM

JOUFSGFSFODF
UP
SBEJP
DPNNVOJDBUJPOT
0QFSBUJPO
PG
UIJT
FRVJQNFOU
JO

B
SFTJEFOUJBM
BSFB
JT
MJLFMZ
UP
DBVTF
IBSNGVM
JOUFSGFSFODF
JO
XIJDI
DBTF

UIF
VTFS
XJMM
CF
SFRVJSFE
UP
DPSSFDU
UIF
JOUFSGFSFODF
BU
IJT
PXO
FYQFOTF

.PEJmDBUJPOT
UP
UIJT
QSPEVDU
XJUIPVU
UIF
FYQSFTT
BVUIPSJ[BUJPO
PG

7FSJT
*OEVTUSJFT
OVMMJGZ
UIJT
TUBUFNFOU

ProDuct iDentification
BCM Repair Kit
quick install
Disconnect and lock out power to the panel. 1.
Disconnect the current sensor strips from the BCM board by unplugging the ribbon 2.
cables.
Attach the adapter boards to the BCM board by plugging into the ribbon cable 3.
headers.
Reconnect the current sensor strips by plugging the ribbon cables into the adapter 4.
board headers.
Locate the connection sites corresponding to the damaged current sensors. 5.
Wire the replacement split-core sensor* (Veris part number H6806C-0050 or
H6806B-0100) to this port.
Snap the new current sensor onto the appropriate conductor. 6.
Reconnect power to the panel.. 7.
See CT installation guides
for agency approvals.
41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1
LEFT
3.6”
(92mm)
3.6”
(92mm)
NORMAL
EXT CT
Note: The AH24 and
AH25 kits contain
two adapter boards
of identical size.
CT Rating Repair Kit* Replacement CT (sold separately)
50A AH24 H6806C-0050
100A AH25 H6806B-0100
* One CT is included in the repair kit. Additional CTs may be purchased as needed.
2.5"
(64 mm)
2.1"
(54 mm)
3.5"
(89 mm)
2.9"
(74 mm)
0.4” x 0.2”
(10 mm x 5 mm)
Slot (2x)
1.2"
(31 mm)
Removable Mounting Bracket
0.7"
(18 mm)
0.5"
(13 mm)
2.1"
(54 mm)
1.0"
(26 mm)
0.6"
(16 mm)
Adapter Board
Replacement Split-Core Current Sensor (sold separately)