Veris Industries H970HCB Install - Manual

6%2)3 CURRENT MONITORING INSTALLATION GUIDE
Z203257-0D PAGE 1 ©2009 Veris Industries USA 800.354.8556 or +1(0)503.598.4564 / [email protected] 07091
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Split-Core Low Current 4-20mA & 0-10 VDC
DC Current Transducer
Installer’s Specifications
Technology Open loop Hall effect
Amperage Range 0 to 50/100/200 ADC (slide switch selectable)
Sensor Supply Voltage 15 to 30VAC/DC
Supply Current 35mA max.
Isolation 600VAC rms
Temperature Range -15° to 60°C (5° to 140°F)
Humidity Range 10-90% RH non-condensing
Output 4-20mA and/or 0-10VDC
Accuracy ±3% F.S. combined linearity, hysteresis, and repeatability
The product design provides for basic insulation only.
)";"3%
0'
&-&$53*$
4)0$,

&91-04*0/

03
"3$
'-"4)
t
'PMMPX
TBGF
FMFDUSJDBM
XPSL
QSBDUJDFT
4FF
/'1"
&
JO
UIF
64"

PS
BQQMJDBCMF
MPDBM
DPEFT
t
5IJT
FRVJQNFOU
NVTU
POMZ
CF
JOTUBMMFE
BOE
TFSWJDFE
CZ
RVBMJmFE
FMFDUSJDBM
QFSTPOOFM
t
3FBE

VOEFSTUBOE
BOE
GPMMPX
UIF
JOTUSVDUJPOT
CFGPSF
JOTUBMMJOH
UIJT
QSPEVDU
t
5VSO
Põ
BMM
QPXFS
TVQQMZJOH
FRVJQNFOU
CFGPSF
XPSLJOH
PO
PS
JOTJEF
UIF
FRVJQNFOU
t
6TF
B
QSPQFSMZ
SBUFE
WPMUBHF
TFOTJOH
EFWJDF
UP
DPOmSN
QPXFS
JT
Põ

%0
/05
%&1&/%
0/
5)*4
130%6$5
'03
70-5"(&
*/%*$"5*0/
t
0OMZ
JOTUBMM
UIJT
QSPEVDU
PO
JOTVMBUFE
DPOEVDUPST
'BJMVSF
UP
GPMMPX
UIFTF
JOTUSVDUJPOT
XJMM
SFTVMU
JO
EFBUI
PS
TFSJPVT
JOKVSZ
%"/(&3
Wiring ExamplE
H970HCB 970HCB
DimEnsions
/05*$&
t
5IJT
QSPEVDU
JT
OPU
JOUFOEFE
GPS
MJGF
PS
TBGFUZ
BQQMJDBUJPOT
t
%P
OPU
JOTUBMM
UIJT
QSPEVDU
JO
IB[BSEPVT
PS
DMBTTJmFE
MPDBUJPOT
t
5IF
JOTUBMMFS
JT
SFTQPOTJCMF
GPS
DPOGPSNBODF
UP
BMM
BQQMJDBCMF
DPEFT
t
.PVOU
UIJT
QSPEVDU
JOTJEF
B
TVJUBCMF
mSF
BOE
FMFDUSJDBM
FODMPTVSF
quick install
Disconnect and lock out power to the conductor to be monitored. 1.
Choose a location for the sensor. The monitored conductor must pass through the 2.
iris, and the sensor must be at least 1/2” from any uninsulated conductors.
Install the adjustable mounting bracket to the back of the enclosure using the 3.
included screws.
Connect 15-30VAC/DC to the terminals marked Power (+) and Gnd (-). 4.
Wire the output (mA or VDC) connections between the sensor and the controller. 5.
Snap the sensor over the conductor to be monitored and clip the assembly to the 6.
mounting bracket.
Set the field-selectable switch to the desired amperage level (see page 2). 7.
Fan or Pump
CONTROLLER
4-20mA DC
Analog
Input
MOTOR
CONTACTOR
Removable Mounting Bracket
Self-gripping
Iris
1.0”
(25 mm)
0.8”
(21 mm)
1.1”
(26 mm)
3.1”
(79 mm)
2.8”
(70 mm)
Ø = 0.3”
(8 mm)
1.4”
(36 mm)
2.5”
(64 mm)
3.0”
(76 mm)
Bracket can be mounted
on either side for added
installation flexibility.
Use DIN Rail
Mounting clip
(Veris part
number AH01) to
mount on stan-
dard DIN rail.