Veris Industries H950 Install - Manual

6%2)3 CURRENT MONITORING INSTALLATION GUIDE
Z201503-0A PAGE 1 ©2009 Veris Industries USA 800.354.8556 or +1(0)503.598.4564 / [email protected] 06091
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Split-Core Current Switch, Fixed Trip Point, with
Command Relay
Installer’s Specifications
Sensor Power Induced from monitored conductor
Insulation Class 600VAC RMS
Frequency Range 50/60Hz
Temperature Range -15° to 60°C (5° to 140°F)
Humidity Range 10-90% RH, non-condensing
Hysteresis 10% Typical
Terminal Block Maximum Wire Size 14 AWG
Terminal Block Torque (nominal) 4 in-lbs (0.45 N-m)
Agency Approvals UL 508 open device listing
Do not use the LED status indicators as evidence of applied voltage.
)";"3%
0'
&-&$53*$
4)0$,

&91-04*0/

03
"3$
'-"4)
t
'PMMPX
TBGF
FMFDUSJDBM
XPSL
QSBDUJDFT
4FF
/'1"
&
JO
UIF
64"

PS
BQQMJDBCMF
MPDBM
DPEFT
t
5IJT
FRVJQNFOU
NVTU
POMZ
CF
JOTUBMMFE
BOE
TFSWJDFE
CZ
RVBMJmFE
FMFDUSJDBM
QFSTPOOFM
t
3FBE

VOEFSTUBOE
BOE
GPMMPX
UIF
JOTUSVDUJPOT
CFGPSF
JOTUBMMJOH
UIJT
QSPEVDU
t
5VSO
Põ
BMM
QPXFS
TVQQMZJOH
FRVJQNFOU
CFGPSF
XPSLJOH
PO
PS
JOTJEF
UIF
FRVJQNFOU
t
6TF
B
QSPQFSMZ
SBUFE
WPMUBHF
TFOTJOH
EFWJDF
UP
DPOmSN
QPXFS
JT
Põ

%0
/05
%&1&/%
0/
5)*4
130%6$5
'03
70-5"(&
*/%*$"5*0/
t
0OMZ
JOTUBMM
UIJT
QSPEVDU
PO
JOTVMBUFE
DPOEVDUPST
'BJMVSF
UP
GPMMPX
UIFTF
JOTUSVDUJPOT
XJMM
SFTVMU
JO
EFBUI
PS
TFSJPVT
JOKVSZ
%"/(&3
Wiring ExamplE
H950 950
DimEnsions
/05*$&
t
5IJT
QSPEVDU
JT
OPU
JOUFOEFE
GPS
MJGF
PS
TBGFUZ
BQQMJDBUJPOT
t
%P
OPU
JOTUBMM
UIJT
QSPEVDU
JO
IB[BSEPVT
PS
DMBTTJmFE
MPDBUJPOT
t
5IF
JOTUBMMFS
JT
SFTQPOTJCMF
GPS
DPOGPSNBODF
UP
BMM
BQQMJDBCMF
DPEFT
t
.PVOU
UIJT
QSPEVDU
JOTJEF
B
TVJUBCMF
mSF
BOE
FMFDUSJDBM
FODMPTVSF
Removable Mounting Bracket
Self-gripping
Iris
1.0”
(25 mm)
0.8”
(21 mm)
1.1”
(26 mm)
3.1”
(79 mm)
2.8”
(70 mm)
Ø = 0.3”
(8 mm)
1.4”
(36 mm)
2.5”
(64 mm)
3.0”
(76 mm)
Bracket can be mounted
on either side for added
installation flexibility.
Use DIN Rail
Mounting clip
(Veris part
number AH01) to
mount on stan-
dard DIN rail.
quick install
Disconnect and lock out power to the conductor to be monitored. 1.
Plan the installation: 2.
Locate a mounting surface for the removable mounting bracket that will allow
the monitored conductor to pass through the iris, or “window” when it is installed
and keep the product at least 1/2” (13mm) from any uninsulated conductors (CE).
Determine cable routing for the controller connection, allowing wiring to reach
the mounting location.
Install mounting bracket 3.
Drill holes to mount the bracket to the chosen surface using the included screws.
Wire the output connections between the sensor and the controller. 4.
Snap thesensor over the wire to be monitored and clip the assembly to the 5.
mounting bracket.
Close up and power up. 6.
Fan or Pump
CONTROLLER
Motor
CONTACTOR
DI (Status)
DO (Relay
Coil)
CONTROL
POWER