Veris Industries SDI SERIES Install User Manual
Page 4
44
correct depth and alignment.
Electronic Outputs
Standard Frequency
Sensor output is a pulse proportional to flow. The
signal is similar to all 200 Series Data Industrial
flow sensors and will interface with all existing
Data Industrial transmitters and monitors. The
power supply to the sensor and the output signal
from the sensor is carried on the same two wires.
Wire connections are made at screw terminals on
removable headers inside the NEMA 4X housing.
Analog Output
The Sensor is also available with a two-wire loop
powered 4-20 mA output. The analog output is
produced by an on-board micro-controller for
precise, drift-free signals. The unit is programmed
from a computer using Windows
based software
and a Data Industrial A-301 connection cable.
Units may be pre-programmed at the factory or
field programmed. All information is stored in
non-volatile memory in the flow sensor.
Scaled Pulse Output
The scaled pulse is produced by an on-board
micro-controller for precise, accurate outputs.
This option may be programmed to produce
an isolated dry contact closure scaled to any
number of engineering units of measure.
Sensors may be pre-programmed at the factory
or field programmed using a Data Industrial
A-301 connection cable and a Windows
based
software program. All information is stored in
non-volatile memory in the flow sensor. This is a
four-wire option.
Bi-directional Flow- Analog Output
This option provides a programmable 4-20 mA
signal proportional to flow rate and a contact
closure to indicate the direction of flow. All
programming is accomplished as previously
mentioned. The user can program the unit for
pipe size, flow scale and the direction of flow.
This is a six-wire option.
Bi-directional Flow- Scaled Pulse Output
This option provides the user with a choice
of outputs. In one case the sensor provides
an output scaled to the required number of
engineering units on one set of terminals and a
contact closure to indicate the direction of flow on
another. The other choice provides two isolated
scaled pulse outputs, one for each direction.
Programming the output choice, pipe size, output
scale and direction of flow by the user are also
accomplished by using a PC with Data Industrial
software and A-301 connection cable. This option
SDI Series Hot Tap Ordering Matrix
SDI
0
H1
N
0
0
-
0
2
0
0
Material
Stainless Steel/PPS Tip
0
Stainless Steel/PEEK Tip
2
Type
Hot Tap for Pipe 1-1/2" thru 10" *
H1
Hot Tap for Pipe 12" thru 36" *
H2
Hot Tap for Pipe 36" and UP*
H3
Electronic Housing
NEMA 4X
N
Output
Standard Frequency Pulse
0
Analog 4-20mA
1
Scaled Pulse
2
Bi-Directional, 4-20mA + Direction [PPS tip Only]
5
Bi-Directional, Scaled Pulse [PPS tip Only]
6
Display
No Display
0
LCD Option [not available with output option 0]
1
O-Ring
Viton
®
0
Shaft
Tungsten Carbide [Standard]
2
Hastelloy
®
C-276 [optional - consult factory]
1
Zirconia Ceramic [optional - consult factory]
0
Impeller
Stainless Steel
0
Bearing
Torlon
®
0
*Pipe size for reference only-Depending on pipe material, tapping saddle, or existing
hardware, longer sensor length may be required. Consult Factory
Viton
®
is a registered trademark of DuPont-Dow Elastomers.
Torlon
®
is a registered trademark of Amoco Performance Products.
Windows
®
is a registered trademark of Microsoft Corporation.
Hastelloy
®
is a registered trademark of Haynes Corporation.
For material details, consult the factory.
SDI Series Direct Insert Ordering Matrix
SDI
0
D1
N
0
0
-
0
2
0
0
Material
Stainless Steel/PPS Tip
0
Brass/PPS Tip
1
Stainless Steel/PEEK Tip
2
Type
Direct Insert for Pipe 1-1/2" thru 10" *
D1
Direct Insert for Pipe 12" thru 36" *
D2
Direct Insert 36" and UP*
D3
Electronic Housing
NEMA 4X
N
Output
Standard Frequency Pulse
0
Analog 4-20mA
1
Scaled Pulse
2
Display
No Display
0
LCD Option [not available with output option 0]
1
O-Ring
Viton
®
0
Shaft
Tungsten Carbide [Standard]
2
Hastelloy
®
C-276 [optional - consult factory]
1
Zirconia Ceramic [optional - consult factory]
0
Impeller
Stainless Steel
0
Bearing
Torlon
®
0
*Pipe size for reference only-Depending on pipe material, tapping saddle, or existing
hardware, longer sensor length may be required. Consult Factory
Viton
®
is a registered trademark of DuPont-Dow Elastomers.
Torlon
®
is a registered trademark of Amoco Performance Products.
Windows
®
is a registered trademark of Microsoft Corporation.
Hastelloy
®
is a registered trademark of Haynes Corporation.
For material details, consult the factory.