Fagor FFJ8845 - Manual (Page 15)

13
1
Instruction manual
Very important: Read this manual carefully before using your refrigerator.
This manual is designed with texts corresponding to drawings.
Installation
Identify the model of your refrigerator (“a”,
“b”, “c”) by comparing the control panel with the
illustrations.
1.1 Unpacking. Remove all protective materials.
1.2 Placement. Place the refrigerator away from
heat sources and protect it from direct sunlight
in order to conserve energy.
Do not install the refrigerator in the open air or
where it is exposed to rain.
Air should be able to circulate behind the
refrigerator. Leave 25 mm between the rear of
the refrigerator and the wall. Do not enclose the
space between the refrigerator and the fl oor or
ceiling with any object.
Level the refrigerator to prevent vibration and
noise. Remember that if the refrigerator is
situated next to a wall or cupboard, it could
make some noise.
In addition, make sure that the trays are
correctly placed and position the containers
with a space between them to prevent
vibration.
1.3 Connecting to power. Let the refrigerator sit
in an upright position for at least 2 hours before
connecting it. Check the information on the
specifi cation plate (220-240V with ground wire)
(1.3.1, 1.3.2).
Do not use adapters or extension leads.
Prevent the cord from coming in contact with
the motor or getting trapped beneath it.
1.4 Changing the side that the door opens from.
Disconnect the refrigerator from the power
outlet and empty the inside of the door.
Remove the upper hinge cover with a fl at blade
screwdriver (1.4.1). Loosen the screws and
remove the hinge mechanism with help of a
screwdriver (1.4.2).
Loosen the connector pressing the tab. (1.4.3).
Remove the refrigerator door (1.4.4). Remove
the controls with a screwdriver, prying it away
using the grooves placed for that purpose
(1.4.5).
Make a notch for the cable on the opposite
0
Identifi cation
e n g l i s h
side, as marked on the casing (1.4.6). Remount
the control panel passing the cable through the
notch you made (1.4.7)
Remove the screw cover from the central
hinge, loosen the screws and remove the hinge
(1.4.8). In the models with three compartments,
swap the top and bottom hinges. Remove the
freezer door (1.4.9).
Loosen the screws of the lower hinge and remove
it. Change the position of the hinge axis and place
it on the opposite side (1.4.10).
Place the lower freezer handle on the
refrigerator door and the lower refrigerator
handle on the freezer door, rotated 180º.
Place the vertical handles on the opposite side
rotating them 180º (1.4.11). If you have a centre
compartment, place the upper handle below,
and the lower handle above, rotated 180º.
Rotate the self-closures and place the one from
the refrigerator on the freezer and vice versa
(1.4.12).
Position the freezer door (1.4.13) and attach the
central hinge (1.4.14). Position the refrigerator
door (1.4.15).
Place the closure mechanism in the upper
hinge space on the opposite side (1.4.16).
Put the cable through the upper hinge and
rotation mechanism and plug it into the door
connector (1.4.17).
Screw in the upper hinge (1.4.18) and put the
cover in place (1.4.19).
2.1 Switching on the refrigerator. Press (2.1.1)
or (2.1.2) until a temperature appears on the
display.
2.2 Confi guration. Press for 5 seconds and
you will see the different confi guration options
(language, date, time, warnings…) (2.2.1).
Select the option that you would like to
confi gure by pressing
(2.2.2). Change the
option by pressing the or key (2.2.3).
Verify by pressing (2.2.4). To exit the menu
press for 5 seconds (2.2.5).
2.3 Selecting the compartment. On combined
refrigerators, the refrigerator, freezer and third
compartment all function separately. Press
to select the compartment until it fl ashes (2.3.1)
and validate by pressing
(2.3.2), or press
the button for the desired compartment: ,
,
(2.3.3).
2
Operation