Altronix eBridge4SPT Installation Instructions - Manual

eBridge4SK - 1 -
PLUS
eBridge1SPR Receiver & eBridge4SPT
Quad Port Transceiver/Managed PoE Switch
eBridge4SK Kit includes - eBridge1SPR and eBridge4SPT
Installation Guide
Rev. 072313
I.T.E. 43KC
Overview:
The eBridge1SPR and eBridge4SPT are CAT5 to Coax cable Ethernet adapters/Media converters that deliver data and
power over the coax cable. The paired set enables fast 10/100 Base-T Ethernet digital communication to be transmitted
over Coax cable. An eBridge1SPR receiver transceives data and sends power over the coax to the eBridge4SPT transceiver.
In turn, the remote eBridge4SPT with its embedded 4 port switch provides 4 outputs under PoE/PoE+ protocol.
The eBridge4SPT has built in IP management, allowing for remote camera reset, monitoring and reporting via various IP
protocols. These plug and play units facilitate system upgrades from a single analog to up to four IP cameras/devices
utilizing existing legacy Coax and eliminating the costs and labor associated with installing new network cabling. In addi-
tion, data transmission and power over the Coax is possible up to 1500 ft. in comparison to 100m (328 ft.) Ethernet maxi-
mum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 3). A maximum range from head end
to the PoE camera/device is 610m (2000 ft.) taking into consideration that up to 100m (328 ft.) of structured cable may be
deployed at each end.
Features:
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and
authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
eBridge1SPR and eBridge4SPT is not intended to be connected to outside plant leads and should be installed indoors
within the protected premises. The eBridge1SPR and eBridge4SPT is intended for indoor use only.
1. eBridge1SPR installation:
a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s mounting hole.
Unit should be mounted in proximity to ethernet switch/network, NVR or video server.
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE approved.
Compliant:
• Incorporates sloc TM (Security Link over Coax) technology.
Input:
• eBridge1SPR - 51-56VDC/100W @ max. power.*
eBridge4SPT - powered by eBridge1SPR.
Power Output:
• eBridge4SPT: 4 ports PoE+ (30W) per port.
• Total output power: 95W
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair Cat-5 or better structured cable.
• Distance: up to 328 ft. (100m).
• Speed: 10/100BaseT, half/full duplex, auto negotiation.
Coax:
• Distance: up to 1,500 ft.
• Connectivity: BNC, RG-59/U or similar.
• Throughput is rated to pass 25mbps from camera to
receiver. Data distances of up to 1500 ft. can be
achieved with the proper headend equipment,
multiple Megapixel cameras can be used.
*UL Listed Class 2 or limited power source
LED Indicators:
• Blue LED - Coax link connection.
• Green LED - Power (eBridge1SPR only).
• Yellow and Green LED (RJ45) IP Link status,
10/100Base-T/active.
Environmental:
• Operating Temperature: 14ºF to 122ºF (--- 10ºC to +50ºC).
• Storage Temperature:
-- 22º to 158ºF (--- 30º to +70ºC) Storage.
• Humidity: 20 to 85%, non-condensing
Applications:
• Retrofit digital IP cameras in an analog CCTV installation
(up to four (4) IP cameras expansion per analog camera).
• Works with Megapixel, HD720, HD1080 and VGA
(SD) cameras (see note, pg. 2).
• Extend Network link distance in an industrial
environment.
• Upgrade deployed CCTV Coax to a digital network
for Retail, Casinos, Airports, Schools, Hospitals, etc.
Mechanical:
• Dimensions (H x W x D approx.):
eBridge1SPR:
4.375” x 3.5” x 1” (111.125mm x 88.89mm x 25.4mm)
eBridge4SPT:
1.7” x 5.23” x 8.93” (43.18mm x 132.84mm x 226.82mm)
sloc is a registered trademark of Intersil Corporation.