Altronix Netway4ESK Installation Instructions - Manual

NetWay4ESK - 1 -
Netway4ESK - 4-Port Managed PoE+ Switch w/Midspan Injector
Kit includes: Netway4ES and Netway1E
Installation Guide
Rev. 072313
I.T.E. 43KC
Overview:
Netway4ES is a 4-Port Managed PoE+ switch which is designed for installation at the the IDF (Intermediate Distribution
Frame). NetWay4ES allows for system expansion by accommodating up to four (4) IP cameras/devices over a single
CAT-5e or higher structured cable. Power is provided by the NetWay1E midspan injector typically located at the MDF
(Main Distribution Frame). Built-in IP management facilitates remote device reset/control and status monitoring.
Features:
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and
authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
NetWay1E/1EV and NetWay4ES is not intended to be connected to outside plant leads and should be installed indoors
within the protected premises. The NetWay1E and NetWay4ES is intended for indoor use only.
1. NetWay1E installation:
a. Attach mounting brackets to NetWay1E for wall mount installation (Fig. 5, pg. 7).
Affix rubber pads to NetWay1E for shelf installation (Fig. 6, pg. 7).
b.
Plug the grounded AC line cord (included) into the IEC 320 connector of the NetWay1E unit. Plug unit
into a reliable earth grounded socket. When using multiple units the sum of the individual name plate ratings
should not exceed the supply circuit rating.
Note: Do not connect to a receptacle controlled by a switch.
c. Connect structured cable from UL Listed ethernet switch or video server to RJ45 jack marked [IN] on
NetWay1E
(Fig. 1, pg. 2).
d. Connect structured cable from NetWay4ES to RJ45 jack marked [OUT] on NetWay1E (Fig. 1, pg. 2).
e. PoE ON LED will illuminate indicating PoE device is turned on (Fig. 1, pg. 2).
f. Connect a device that will provide a low voltage trigger input to terminals marked [--- PoE Shutdown +]
(12VAC-24VAC or 5VDC-24VDC) (PoE Shutdown Voltage Range in Specifications).
When voltage is applied the PoE output will drop to zero volts. When the voltage is removed from the
PoE shutdown terminals the PoE output will supply power to PoE compliant devices (normal condition).
Note: Return to normal operation from shutdown can take about 4 seconds. When PoE is disabled devices may
still present data signals on line pairs of the structured cable.
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE approved.
Input:
• 84W from Netway1E.
Power Output:
• Maximum power per port: PoE+ (30W).
• Total maximum power: 84W.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair Cat-5 or better structured cable.
• Distance: up to 328 ft. (100m).
• Speed: 10/100BaseT, half/full duplex, auto negotiation.
LED Indicators:
NetWay1E
- AC Power.
- Yellow - IP Link status, Green - 10/100Base-T/active.
LED Indicators (cont’d):
NetWay4ES
- Yellow - IP Link status, Green - 10/100Base-T/active.
Environmental:
• Operating Temperature: 14ºF to 122ºF (--- 10ºC to +50ºC).
• Storage Temperature:
-- 22º to 158ºF (--- 30º to +70ºC) Storage.
• Humidity: 20 to 85%, non-condensing
Applications:
• Remote installation and powering of a managed
4 port PoE+ switch. Star expansion of remote node to
4 PoE+ cameras/devices.
Mechanical:
• Dimensions (H x W x D approx.):
1.7” x 5.23” x 8.42” (43.18mm x 132.84mm x 213.87mm)
®