Altronix ReServ4WP Installation Instructions - Manual

- 1 - ReServ
Overview:
ReServ4 Video Surveillance UPS unit is designed to provide power for 24VAC and 12VDC cameras during normal or
power outage conditions. True sine wave regulated AC outputs and/or regulated DC outputs.
Specifications:
Stand-by Specifications:
Stand-by Batteries 4 amp (100VA) load at 24VAC and 1 amp load at 12VDC max.
Two (2) 12VDC/7AH 45 minutes
Two (2) 12VDC/12AH 90 minutes
Installation Instructions:
This installation should be made by qualified service personnel and should conform to all local codes and in accordance
with the National Electrical Code. Product is intended for indoor use only. This product contains no serviceable parts.
1. Mount unit in desired location. Mark & predrill holes in the wall to line up with the top two keyholes in the enclosure.
Install two upper fasteners & screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes
over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the enclosure. Drill the
lower holes and install the two fasteners. Place the enclosure’s upper keyholes over the two upper screws. Install the
two lower screws and make sure to tighten all screws (Enclosure, pg. 4). Secure enclosure to earth ground.
Note: This product needs to be secured to the building before operation.
2. Connect AC power mains to terminals marked [L & N], connect ground to terminal marked [G] (Fig. 1, pg. 3).
Use 18 AWG or larger for all power connections (Battery, output) (Fig. 1, pg. 3).
Use 18 AWG to 22 AWG for power limited circuits (AC Fail/Low Battery reporting) (Fig. 1, pg. 3).
Note: A readily accessible disconnect device shall be incorporated in the building installation wiring.
3. The LEDs on the power supply board will illuminate when AC power is present.
4. Measure output voltage before connecting cameras/devices to outputs. This helps avoid potential damage.
5. Connecting Fluidmesh Wireless Radio/Bosch Autodome:
Connect 12VDC Fluidmesh Wireless Radio to terminals marked [P 1-2, N 1-2] (Fig. 1, pg. 3).
Connect 24VAC Bosch Autodome to terminals marked [15-16] (Fig. 1, pg. 3).
6. Connect batteries to terminals marked [-- BAT + ] (Fig. 1, pg. 3). Use two (2) 12VDC batteries connected in
series for 24VDC operation (battery leads included).
Use batteries - Casil CA1270 (12V/7AH), Genesis NP7-12 (12V/7AH), Ultratech UT1270 (12V/7AH).
7. Connect appropriate signaling notification devices to AC FAIL & BAT FAIL (Fig. 1, pg. 3) supervisory relay outputs.
8. The power LEDs on the unit for Outputs 1-2 & 15-16 will illuminate when AC power is present (Fig. 1, pg. 3).
Note: If any of the power LEDs are not illuminated the cause may be due to the following:
a. AC mains and battery fail.
b. One (1) or more power output PTCs are tripped due to a short circuit or overload condition.
c. Unit damaged/defective. To reset the PTC:
1. Temporarily remove wiring from output with tripped PTC (Fig. 1, pg. 3).
2. Eliminate the trouble condition (short circuit or overload).
3. Allow 1 minute for PTC to cool off (reset).
4. Re-attach wiring to the output (Fig. 1, pg. 3).
5. Power LEDs will illuminate indicating power has been restored to outputs (Fig. 1, pg. 3).
Input:
• 115VAC 60Hz, 3.5 amp.
Output:
• PTC protected outputs:
- 24VAC @ 4 amp max.
- 12VDC @ 1 amp.
Battery Backup:
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switchover to stand-by battery when AC fails.
Supervision:
• AC fail & low battery supervision (form “C” contacts).
Visual & Audio Indicators:
• AC/DC power LED indicators.
Visual Indicators:
• Individual power output LED indicators.
• Low voltage input and Shutdown LED indicators.
Additional Features:
• True sine wave regulated AC outputs &
regulated DC outputs.
• Unit maintains camera synchronization.
• Ease of installation saves time and eliminates costly labor.
Enclosure Dimensions:
• NEMA4 / IP66 Rated enclosure accommodates up to
two (2) 12VDC/7AH batteries.
17.5”H x 12”W x 6.625”D
ReServ4WP - Outdoor Video Surveillance UPS