Altronix eBridge1CRT Installation Instructions - Manual

eBridge1CRT - 1 -
Overview:
The eBridge1CT and eBridge1CR are CAT5 to Coax cable Ethernet adapters. The paired set enables fast 10/100Base-T
Ethernet digital communication to be transmitted over Coax cable. These plug and play units facilitate system upgrades
from analog to IP cameras/devices utilizing existing legacy Coax and eliminating the costs and labor associated with install-
ing new network cabling. In addition data transmission over the Coax is up to 1500’ (five times the 100m/328ft Ethernet
maximum length). At the same time the units can combine Composite Video Signal with the Ethernet data enabling con-
nection to an analog input on a monitor or matrix switch.
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and
authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
eBridge1CT and eBridge1CR are not intended to be connected to outside plant leads and should be installed indoors
within the protected premises. eBridge1CT and eBridge1CR are intended for indoor use only.
1.
eBridge1CR installation:
a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s mounting hole
(Fig. 2a, pg. 3). Unit should be mounted in proximity to ethernet switch/network, NVR or video server.
b. Connect 16VAC/24VAC Class 2 plug-in transformer or 12VDC/24VDC (polarity not observed) Class 2 power
supply to jack marked [Power Input] utilizing barrel connector (supplied) (Fig. 1, pg. 2).
Use 22AWG-16AWG wire for this connection.
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE approved.
• C-Tick complant.
Compliant:
• Incorporates *sloc TM (Security Link over Coax) technology.
Input:
• 12VDC to 24VDC Class 2 power supply (polarity not
observed) or 16VAC to 24VAC Class 2 plug-in
transformer.
Power Consumption:
• eBridge1CR/eBridge1CT:
12VDC/275mA, 24VDC/110mA,
16VAC/375mA, 24VAC/200mA.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair Cat-5 or better structured cable.
• Distance: up to 328 ft. (100m).
• Speed: 10/100BaseT, half/full duplex, auto negotiation.
• Throughput is rated to pass 25mbps of data at
distances up to 1500 ft. With proper headend
equipment, multiple Megapixel cameras can be used.
Coax:
• Distance: up to 1,500 ft.
• Connectivity: BNC, RG-59/U or similar.
LED Indicators:
• Blue LED - Coax link connection.
• Yellow and Green LED (RJ45) IP Link status,
10/100Base-T/active.
• Green LED - Power.
Environmental:
• Operating Temperature: 14ºF to 122ºF (--- 10ºC to +50ºC).
• Storage Temperature:
-- 22º to 158ºF (--- 30º to +70ºC) Storage.
• Humidity: 20 to 85%, non-condensing
Accessories:
• Composite video cables (included) - enables simultaneous
composite video signal over the same Coax.
• Two (2) power connectors.
Applications:
• Retrofit digital IP cameras in an analog CCTV
installation.
• Works with Megapixel, HD720, HD1080 and VGA
(SD) cameras (see note, pg. 2).
• Extend Network link distance in an industrial
environment.
• Upgrade deployed CCTV Coax to a digital network
for Retail, Casinos, Airports, Schools, Hospitals, etc.
• Enables simultaneous transmission of composite and
digital IP video.
Mechanical:
• Dimensions (W x L x H approx.):
2.5” (63.5mm) x 3.8” (96.52mm) x 1” (25.4mm)
Features:
eBridge1CRT - IP over Coax Solution
eBridge1CR Receiver and eBridge1CT Transceiver Kit
Installation Guide
Rev. 070612
* sloc is a registered trademark of Intersil Corporation.
I.T.E. 43KC
Z1409