Altronix HubWay Dvi Installation Instructions - Manual

HubWayAv, HubWayDv and HubWayDvi
Video Balun/Combiners
Video Balun/Combiner Reference Chart:
Fig. 1
Fig. 1a
Fig. 1b
HubWaAV/DV/Dvi - 1 -
Agency Listings:
• UL Listed accessory for Commercial
CCTV Equipment (UL 2044).
Data:
• Data/PTZ RS422/RS485 output.
Video:
• 75 ohm video input.
Visual Indicators:
• Power LED indicator.
Specifications:
Installation Instructions:
1. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel 1] of
the HubWay, HubWayLD, or HubSat Series (Please refer to respective Installation Instructions).
Plug the RJ45 connector at the opposite end of the structured cable into the RJ45 jack of the
Video Balun/Combiner installed at camera 1.
• For 24VAC Cameras use Altronix model HubWayAv (Figs. 1a, 1b, pg. 1).
• For 12VDC Cameras use Altronix model HubWayDv/Dvi (Figs. 1c, 1d, pg. 1).
Repeat this step for cameras 2-8.
Note: When an installation exceeds the maximum distance for power transmission, a local external
power source is required. Optionally, an Altronix HubSat4D Passive UTP Transceiver Hub
w/Integral Power may be utilized (Fig. 2, pgs. 2-3). The combined total cable distance between the
HubWay, HubWayLD Series and each camera routed through the HubSat4D
must not exceed 3000 ft.
2. Measure the output voltage at each Video Balun/Combiner before connecting camera power
(Figs. 1a-1d, pg. 1). This helps avoid potential damage.
• HubWayAv - Terminals marked [AC POWER] (Figs. 1a, 1b, pg. 1).
• HubWayDv/Dvi - Terminals marked [– 12VDC +] (Figs. 1c, 1d, pg. 1).
3. Connect the power outputs of the HubWayAv or HubWayDv Video Balun/Combiners to the power
input terminals of the cameras (Figs. 1a-1d, pg. 1).
4. Connect the terminals marked [+ DATA -- ] of the HubWayAv or HubWayDv Video Balun/Combiners
to the data terminals of the cameras for PTZ control (Figs. 1a-1d, pg. 1). Polarity must be observed.
When using fixed cameras disregard this step (Figs. 2, pgs. 2-3).
5. Connect the BNC connector of the HubWayAv. HubWayDv or HubWayDvi Video Balun/Combiners
to the BNC video outputs of the cameras (Figs. 1a-1d, pg. 1).
1
1 - White/Orange [VIDEO +]
2 - Orange [VIDEO -]
3 - White/Green [DATA +]
4 - Blue [AC 1]
5 - White/Blue [AC 2]
6 - Green [DATA -]
7 - White/Brown [AC 2]
8 - Brown [AC 1]
2 3 4 5 6 7 8
Fig. 3 - CAT-5 Structured Cable Wiring Color Codes
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
website: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.
IIHubWay Video Balun/Combiners Rev. 123008
A16I MEMBER
- 4 - HubWaAV/DV/Dvi
Overview:
HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners are UL Listed
accessories to be used with HubWay, HubWayLD and HubSat series. These Altronix
Passive and Active UTP Transceiver Hubs w/Integral Power route Video/Data and
Power from Altronix HubWay, HubWayLD and HubSat units for either 24VAC or 12VDC
fixed or PTZ indoor or outdoor cameras.
Note: Refer to HubWay series Rev. 032108, HubWayLD series Rev. 030408 or
HubSat series Rev. 112408 installation guides.
AC Power
to Camera
Data to
Camera --
+ Data to
Camera
Green Power LED
12VDC Power
to Camera +
--
Red Power LED
Wire
Connectors RJ45 Jack RJ45 Jack
To BNC
Connector
of Camera
To BNC
Connector
of Camera
Structured
Cable from
HubWay,
HubWayLD or
HubSat
Structured
Cable from
HubWay8D
or
HubWay16D --
+
Wire
Connectors
* Also Available as:
HubWayDvi
Video Balun/
Combiner
for non-isolated
12VDC cameras
Refer to the HubWay Video Balun/Combiner
Installation Guide Rev. 123008
AC
POWER RJ45
DATA
+ --
VIDEO Commercial
CCTV Accessory
3C03
HubWayAv VIDEO BALUN/COMBINER
Refer to the HubWay Video Balun/Combiner
Installation Guide Rev. 123008
12VDC
-- + RJ45
DATA
+ --
VIDEO Commercial
CCTV Accessory
3C03
HubWayDv VIDEO BALUN/COMBINER
HubWayAv passes AC voltage from pins 4, 5,
7, 8 to terminals marked [AC Power]
(Fig. 3, pg. 4). HubWayDv/Dvi converts AC voltage to DC
voltage from pins 4, 5, 7, 8 to terminals marked
[-- 12VDC +] (Fig. 3, pg. 4).
HubWayAv *24VAC/28VAC *24VAC/28VAC 1 amp 24VAC cameras Green
HubWayDv *24VAC/28VAC 12VDC 1 amp 12VDC cameras Red
HubWayDvi *24VAC/28VAC
12VDC electronically
isolated
.5 amp
12VDC cameras
without isolation
Red
Altronix
Model Number
Output
V
oltage
to
camera
Input
V
oltage
from
HubW
ay
unit
Output
Ratings
(max.)
*Based on camera load and structured cable length.
Po
w
er
LED
Fig. 1c
Fig. 1d
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or
moisture. This installation should be made by qualified service personnel and should conform to
all local codes.
Camera
Type