Altronix eBridge16PCRX Data Sheet - Manual

The eBridge16PCRX is a CAT5 to Coax cable Managed Ethernet Midspan
receiver. The receiver enables fast 10/100Base-T Ethernet digital com-
munication to be received over Coax cable. An eBridge16PCRX receiver
sends power over the coax to the eBridge1PCT 15.4W (PoE) or eBridge-
1PCTX 30W (PoE+) transmitter under PoE protocol.
The eBridge1PCT/PCTX in turn delivers that power to a PoE enabled
camera or IP device. The eBridge16PCRX will not deliver power to non
compliant devices, thus avoiding accidental power turn into improperly con-
nected analog cameras. These plug and play units facilitate system upgrades from analog to IP cameras/devices utilizing
existing legacy Coax and eliminating the costs and labor associated with installing new network cabling. In addition,
data transmission and power over the Coax is possible up to 1500 ft. in comparison to 100m (328 ft.) Ethernet maximum
distance. A maximum range from head end to the PoE camera/device is 610m (2000 ft.) taking into consideration that
up to 100m (328 ft.) of structured cable may be deployed at each end.
eBridge16PCRX - IP over Coax Receiver
Rev. DSeBridge16PCRX_08012013
Specifications
Overview
Agency Approvals
UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
European Conformity
* sloc is a registered trademark of Intersil Corporation.
eBridge16PCRX
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE approved.
Compliant:
• Incorporates *sloc TM (Security Link over Coax)
technology.
Input:
• 48VDC to 56VDC UL Listed power supply
(attention to observe polarity).
Note: Use 54V to 56V power supply to achieve
full power per IEEE802.3 at standard.
Power Consumption
(per input for max. load; 2 inputs, each powers
8 channels) :
• 48VDC/6A, 56VDC/6A per Input,
Total current 12A.
eBridge1PCTX (30W): Powered by eBridge16PCRX.
eBridge1PCT (15W): Powered by eBridge16PCRX.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair Cat-5 or better structured cable.
• Distance: up to 328 ft. (100m).
• Speed: 10/100BaseT, half/full duplex, auto negotiation.
• Throughput is rated to pass 25mbps of data at
distances up to 1500 ft. With proper headend
equipment, multiple Megapixel cameras can be used.
Coax:
• Distance: up to 1,500 ft.
• Connectivity: BNC, RG-59/U or similar.
LED Indicators:
• Blue LED - Coax link connection.
• Yellow and Green LED (RJ45) IP Link status,
10/100Base-T/active.
• Green LED - Power.
Environmental:
• Operating Temperature:
14ºF to 122ºF (--- 10ºC to +50ºC).
• Storage Temperature:
-- 22º to 158ºF (--- 30º to +70ºC) Storage.
• Humidity: 20 to 85%, non-condensing
Applications:
• Retrofit digital IP cameras in an analog CCTV
installation.
• Works with Megapixel, HD720, HD1080 and VGA
(SD) cameras.
• Extend Network link distance in an industrial
environment.
• Upgrade deployed CCTV Coax to a digital network
for Retail, Casinos, Airports, Schools, Hospitals, etc.
Accessories:
• eBridge1PCT: Single port ethernet/PoE transceiver.
• eBridge1PCTX: Single port ethernet/PoE or PoE+
transceiver.
•
VertiLine563: 56VDC Rack Mount Power Supply/
Charger.
•
RE2: Rack mount battery enclosure. Accommodates
up to four 12VDC/7AH batteries (batteries not included).
Mechanical:
• Dimensions (H x W x D approx.):
1.625” x 19.125” x 8.5” (41.275mm x 486mm x 216mm)
C-Tick Approved - Z1409