Altronix eBridge1PCRTX Installation Instructions - Manual

eBridge1PCRX/PCTX - 1 -
PLUS
Overview:
The eBridge1PCRX and eBridge1PCTX are CAT5 to Coax cable Ethernet adapters media converters that deliver data and
power over the coax cable in a PoE+ compliant format. The paired set enables fast 10/100Base-T Ethernet digital commu-
nication to be transmitted over Coax cable. An eBridge1PCRX receiver sends power over the coax to the eBridge1PCTX
transmitter under PoE protocol. The eBridge1PCTX in turn delivers that PoE+ compliant power to a PoE enabled camera
or IP device. The eBridge1PCRX will not deliver power to non compliant devices, thus avoiding accidental power turn into
improperly connected analog cameras. These plug and play units facilitate system upgrades from analog to IP cameras/
devices utilizing existing legacy Coax and eliminating the costs and labor associated with installing new network cabling.
In addition, data transmission and power over the Coax is possible up to1500 ft. in comparison to 100m (328 ft.) Ethernet
maximum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 3). A maximum range from head
end to the PoE camera/device is 610m (2000 ft.) taking into consideration that up to 100m (328 ft.) of structured cable may
be deployed at each end.
Features:
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE approved.
• C-Tick compliant.
Compliant:
• Incorporates *sloc TM (Security Link over Coax) technology.
Input:
• 24VDC to 56VDC Class 2 power supply
(polarity observed).
Power Consumption (under maximum load):
• eBridge1PCRX: 24VDC/1,500mA, 56VDC/900mA.
eBridge1PCTX (30W): Powered by eBridge1PCRX.
eBridge1PCT (15W): Powered by eBridge1PCRX.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5 or better structured cable.
• Distance: up to 100m (328 ft.).
• Speed: 10/100BaseT, half/full duplex, auto negotiation.
PoE compliant to IEEE 802.3af (15W) and PoE+
compliant to IEEE 802.3at (30W) Delivered to
camera by eBridge1PCTX. Power provided by
eBridge1PCRX to eBridge1PCTX by PoE protocol.
• Throughput is rated to pass 25mbps of data at
distances up to 1500 ft. With proper headend
equipment, this supports Megapixel, HD720, HD1080.
Coax:
• Distance: up to 1,500 ft. (see Maximum Length of Coax
Type vs. Camera Power/PoE Class, pg. 3) for power
delivery of coax.
• Connectivity: BNC, RG-59/U or similar.
LED Indicators:
• eBridge1PCRX:
Blue LED - Coax link connection (sloc).
Green - PoE ON.
Green - Power ON.
LED Indicators (cont’d):
• eBridge1PCRX:
Yellow and Green LED (RJ45) IP Link status,
10/100Base-T/active.
• eBridge1PCTX:
Blue LED - Coax link connection (SLOC).
Green LED - PoE from eBridge1PCR.
Environmental:
• Operating Temperature:
eBridge1PCRX:
15W: -- 4ºF to 113ºF (-- 20ºC to +45ºC).
30W for 24VDC: -- 4ºF to 98.6ºF (-- 20ºC to +37ºC).
30W for 48VDC: -- 4ºF to 113ºF (-- 20ºC to +45ºC).
eBridge1PCTX: --- 4ºF to 120.2ºF (-- 20ºC to +49ºC).
• Storage Temperature:
-- 22º to 158ºF (-- 30º to +70ºC) Storage.
• Humidity: 20 to 85%, non-condensing
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
• Retrofit digital IP cameras in an analog CCTV
installation.
• Works with Megapixel, HD720, HD1080 and VGA
(SD) cameras (see note, pg. 2).
• Extend Network link distance in an industrial
environment over 610m (2000 ft.) (see note, pg. 2).
• Upgrade deployed CCTV Coax to a digital network
in Retail, Casinos, Airports, Schools, Hospitals, etc.
Mechanical:
• Dimensions (W x L x H approx.):
eBridge1PCRX:
3.5” x 4.375” x 1” (88.89mm x 111.125mm x 25.4mm)
eBridge1PCTX:
2.5” x 4.375” x 1” (63.5mm x 111.125mm x 25.4mm)
eBridge1PCRTX - IP and PoE+ over Coax Solution
eBridge1PCRX Receiver and eBridge1PCTX Transceiver kit
Installation Guide
Rev. 022213
I.T.E. 43KC
Z1409
* sloc is a registered trademark of Intersil Corporation.