Altronix AL400ULACM Data Sheet - Manual

AL400ULACM converts a 115VAC 60Hz input into eight (8) independently controlled
12VDC or 24VDC Fail-Safe and/or Fail-Secure outputs with a total of 4 amp @ 12VDC
or 3 amp @ 24VDC continuous supply current. Outputs are activated by an open collec-
tor sink or normally open (NO) dry trigger input from an Access Control System, Card
Reader, Keypad, Push Button, PIR, etc. This unit will route power to a variety of access
control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders,
etc. The outputs will operate in both Fail-Safe and/or Fail-Secure modes. This unit is
designed to be powered by one common power source (factory installed) which will pro-
vide power for both the board operation and locking devices, or two (2) totally indepen-
dent power sources, one (1) providing power for board operation and the other for lock /
accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or
may be used to trigger other auxiliary devices. The fire alarm disconnect feature is indi-
vidually selectable for any or all of the eight (8) outputs.
AL400ULACM
Power Supply/Chargers w/Multi-Output
Access Power Controllers
Rev. DSAL400ULACM_11062012
Overview
Specifications
AL400ULACM
Input:
• Input 115VAC 60Hz rated @ 1.9 amp.
• Power supply input options:
a) One (1) common power input for ACM8/
ACM8CB and lock power (factory installed).
b)Two (2) isolated power inputs - One (1)to power the
ACM8/ACM8CB and one (1) for lock
accessory power, (external power supply is
required). (Current is determined by the
power supply connected, not to exceed a
maximum of 10 amp total).
• Eight (8) Access Control System trigger inputs.
Input options:
a) Eight (8) normally open (NO) inputs.
b)Eight (8) open collector inputs.
c) Any combination of the above.
Output:
• 12VDC or 24VDC outputs.
• 12VDC @ 4 amp supply current
or 24VDC @ 3 amp supply current.
• Class 2 Rated power limited outputs.
• Eight (8) independently controlled outputs.
Output options:
a) Eight (8) Fail-Safe and/or Fail-Secure power outputs.
b)Eight (8) form “C” 5 amp rated relay outputs
c) Any combination of the above.
• Eight (8) auxiliary power outputs (unswitched)
• Output ratings:
- Fuses are rated @ 3.5 amp.
• Filtered and electronically regulated outputs
(built-in power supply).
Features:
• Fire Alarm disconnect (latching or non-latching) is
individually selectable for any or all of the
eight (8) outputs.
Features (cont’d):
• Fire Alarm disconnect input options:
a) Normally open (NO) or normally closed (NC)
dry contact input.
b)Polarity reversal input from FACP signaling circuit.
• Alarm output relay indicates that FACP input is
triggered (form “C” contact rated @ 1 amp 28VDC
not evaluated by UL).
• Short circuit and thermal overload protection.
Visual Indicators:
• Red LEDs indicate outputs are triggered
(relays energized).
• Green LED indicates FACP disconnect is triggered.
• AC input and DC output LED indicators.
Battery Backup:
• Built-in charger for sealed lead acid or gel type batteries.
• AL400ULXB (Power Supply Board) maximum
charge current 0.7 amp.
• Automatic switch over to stand-by battery when AC fails.
• Zero voltage drop when unit switches over to battery
backup (AC failure condition).
• Battery fail and battery presence supervision
(form “C” contact).
Electrical:
• Operating temperature: 0º C to 49º C ambient.
• ACM8 board main fuse is rated at 10 amp.
• BTU/Hr.:
- 12VDC: 24.57 BTU/Hr.
- 24VDC: 36.85 BTU/Hr.
Mechanical:
• Enclosure Dimensions (H x W x D approx.):
115.5” (393.7mm) x 12” (304.8mm) x 4.5” (114.3mm)
- Combination knockouts are 0.625” and 0.75”
- Accommodates up to two (2) 12AH batteries.
• Product weight (approx.): 10.7 lbs. (4.85 kg).
• Shipping weight (approx.): 12 lbs. (5.44 kg).