Altronix ALTV615DC8UL3 Installation Instructions User Manual
Altv615dc8ul cctv camera & accessory power supply, Overview, Specifications
Overview:
The Altronix ALTV615DC8UL CCTV Power Supply is designed with eight (8) individually fused power limited, Class 2
Rated outputs for powering CCTV Cameras and other video accessories. It will provide 6VDC-15VDC distributed via
eight (8) fused outputs with a total of up to 4 amp continuous supply current.
Specifications:
Agency Listings:
• UL Listed for Commercial Closed-Circuit Television Equipment (UL 2044).
• CUL Listed - CSA Standard C22.2 No.1-98, Audio, Video and Similar Equipment.
Input:
• Input 115VAC 50/60 Hz, .9 amp.
Output:
• 6VDC-15VDC adjustable output.
• Eight (8) individually fuse protected power limited,
Class 2 Rated outputs.
• 4 amp total continuous supply current.
• Filtered and electronically regulated outputs.
Fuse Ratings:
• Output fuses are rated at 3.5 amp/250VAC (Fig. 1).
Visual Indicators:
• AC input and DC output LED indicators.
Additional Features:
• Spare fuses included.
• Unit maintains camera synchronization.
• Ease of installation saves time and eliminates costly labor.
Enclosure Dimensions:
13.5"H x 13"W x 3.25"D
Note: Add suffix “3” for 3-wire line cord
(e.g. ALTV615DC8UL3) and disregard
installation instruction number two (2).
Installation Instructions:
1. Mount ALTV615DC8UL in desired location.
2. Connect green lead to earth ground. Connect AC (115VAC 50/60 Hz) to the black and white flying leads of the
transformer (Fig. 1). Use knockout adjacent to the transformer 1/4” spacing must be provided between AC input
wiring and all other circuits.
3. Adjust output voltage using trimpot on the board prior to connecting CCTV devices.
4. Measure output voltage before connecting devices. This helps avoid potential damage.
Terminals marked [1P-8P] are positive (+) and terminals marked [1N-8N] are negative.
CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting the
output voltage.
5. Connect each DC CCTV cameras to terminal pairs marked [1P-1N thru 8P-8N] on PD8 board carefully
observing correct polarity (Fig. 1).
6. Green LED will illuminate when when unit is powered.
7. Upon completion of wiring, secure enclosure door with screws (supplied).
Keep power limited circuits (outputs 1 through 8) away from non-power limited, 1/4” space must be provided.
Use separate knockouts.
Caution: Equipment to be installed / serviced by authorized / trained personnel only.
Shut branch circuit power before installing / servicing equipment.
ALTV615DC8UL
CCTV Camera & Accessory Power Supply
Rev. 042806
Wire
Strap
(from
Enclosure
to Door)
+
D
C
O
U
T
P
U
T
---
--- BAT +
AC
AC
D
C
A
C
N
C
O
M
M
O
N
P
O
W
E
R
O
U
T
P
U
T
S
P
F
U
S
E
D
P
O
W
E
R
O
U
T
P
U
T
S
1
2
3
4
5
6
7
8
D
1
IN
P
U
T
R
1
L
E
D
XFMR
Black
Lead
White
Lead
Green
Lead
115VAC input
50/60 Hz,
.9 amp
non power-
limited
V
o
lt
a
g
e
A
d
ju
s
tm
e
n
t
Use separate
knockouts for
power-limited
circuits.
Class 2 Not Wet/
Class 3 Wet
Fig. 1