C&H Technology PM75CL1A120 - Manual (Page 4)

PM75CL1A120
Intellimod™ L1-Series
Three Phase IGBT Inverter
75 Amperes/1200 Volts
3
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 www.pwrx.com
03/10 Rev. 1
Electrical and Mechanical Characteristics, T
j
= 25°C unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Units
Control Sector
Circuit Current I
D
V
D
= 15V, V
CIN
= 15V, V
N1
-V
NC
— 6 12 mA
V
D
= 15V, V
CIN
= 15V, V
*P1
-V
*PC
— 2 4 mA
Input ON Threshold Voltage V
th(on)
Applied between U
P
-V
UPC
, 1.2 1.5 1.8 Volts
Input OFF Threshold Voltage V
th(off)
V
P
-V
VPC
, W
P
-V
WPC
, U
N
- V
N
- W
N
-V
NC
1.7 2.0 2.3 Volts
Short Circuit Trip Level SC -20°C ≤ T
j
≤ 125°C, V
D
= 15V 150 — — Amperes
Short Circuit Current Delay Time t
off(SC)
V
D
= 15V — 0.2 — µs
Over Temperature Protection OT Trip Level 135 — — °C
(Detect T
j
of IGBT Chip) OT
(hys)
Hysteresis Level — 20 — °C
Supply Circuit Under-voltage Protection UV Trip Level 11.5 12.0 12.5 Volts
(-20 ≤ T
j
≤ 125°C) UV
R
Reset Level — 12.5 — Volts
Fault Output Current* I
FO(H)
V
D
= 15V, V
CIN
= 15V — — 0.01 mA
I
FO(L)
V
D
= 15V, V
CIN
= 15V — 10 15 mA
Fault Output Pulse Width* t
FO
V
D
= 15V 1.0 1.8 — ms
Thermal Characteristics
Characteristic Symbol Condition Min. Typ. Max. Units
Junction to Case Thermal Resistance R
th(j-c)Q
IGBT (Per 1 Element) (Note 1) — — 0.21 °C/Watt
R
th(j-c)D
FWDi (Per 1 Element) (Note 1) — — 0.36 °C/Watt
Contact Thermal Resistance R
th(c-f)
Case to Fin Per Module, — — 0.038 °C/Watt
Thermal Grease Applied (Note 1)
Recommended Conditions for Use
Characteristic Symbol Condition Value Units
Supply Voltage V
CC
Applied across P-N Terminals ≤800 Volts
Control Supply Voltage** V
D
Applied between V
UP1
-V
UPC
, 15.0 ± 1.5 Volts
V
VP1
-V
VPC
, V
WP1
-V
WPC
, V
N1
-V
NC
Input ON Voltage V
CIN(on)
Applied between U
P
-V
UPC
, ≤0.8 Volts
Input OFF Voltage V
CIN(off)
V
P
-V
VPC
, W
P
-V
WPC
, U
N
- V
N
- W
N
-V
NC
≥9.0 Volts
PWM Input Frequency f
PWM
— ≤20 kHz
Arm Shoot-through Blocking Time t
DEAD
Input Signal ≥2.5 µs
*Fault output is given only when the internal SC, OT and UV protections schemes of either upper or lower arm device operates to protect it.
** With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak.
Note 1: T
C
(under the chip) Measurement Point
Arm UP VP WP UN VN WN
Axis IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi
X 27.8 27.8 65.4 65.4 87.4 87.4 38.7 38.7 54.5 54.5 76.5 76.5
Y -8.0 0.0 -8.0 1.0 -8.0 1.0 -1.4 7.6 -1.4 7.6 -1.4 7.6
Y BOTTOM VIEW
X