Atdec Telehook TH-30-50-RW Installation manual - Manual

Component Checklist
Bits Box
Mounting
Screws
Installation Instructions
TELEHOOK
30”-50” UNIVERSAL ROTATING WALL MOUNT
Attaching the Display to the Wall Plate C
Mounting the Wall Plate A
Masonry Wall Timber Stud Wall
Adjusting the Pivot Head to suit the weight of the
Display
The Pivot head is factory set to hold
approximately 35kgs (77lbs). If the display is not
holding its position when placed on the wall it
may be necessary to remove the display from
the wall and tighten the M12 Hex Nut on the
back of the Pivot Head using a 17mm (
11 / 16 ”)
socket wrench or shifter. To achieve a one-touch
effortless adjustment setting it is advised that the
nut be tightened at half turns and re-tested, until
the desired friction is achieved. Alternatively the
M12 Hex Nut can be over tightened in order to
lock the display in position.
Bracket (x2)
Pivot Head
Extension Plate
Wall Plate
Bracket Plate (x2)
Coach
Screw (x4)
Masonry Wall
Plug (x4)
Large
Washer (x4)
Multi
Washer (x4)
Spacer
Bush (x4)
M6x16mm Socket
Drive Screw (x12)
M8x20mm
Phillips Head
Screw (x4)
M6x16mm
Phillips Head
Screw (x6)
M5x16mm
Phillips Head
Screw (x6)
Allen Key
Small
Washer (x4)
Large Washer
Masonry
Wall Plug
Wall Plate
12mm ( 1 / 2 ”)
Hole
TIP: Use a spirit
level to ensure the
wall plate is
horizontal
Note: Ensure the Wall Plate
is mounted with the narrow
end of the Mounting Slot
at the bottom.
Coach Screw
Note: Ensure the Wall Plate is
mounted with the narrow end of the
Mounting Slot at the bottom.
Large
Washer
Coach Screw
8mm ( 5 / 16 ”)
Hole
Timber
Stud
With the mount attached to the display, lift the
display and slide the Back Plate into the Mounting
slots to ensure a secure connection.
Tighten
M12 Hex Nut
Security Option D
For additional security,
it is suggested that a
Padlock be attached to
the Back plate as shown.
The Padlock (not supplied)
should have a shackle
diameter no larger than
4mm (
3 / 16 ”).
Padlock
Note: This procedure will require two persons
Back Plate
Mounting
Slots
Mounting Slot
Note: For demonstration purposes, the display
has been omitted from the image below.
Back plate
Shackle 4mm ( 3 / 16 ”)
diameter or less
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 18.04.07 ©
Important Notes
TOOLS REQUIRED:
Power Drill
12mm or 8mm Drill Bit
Phillips Head Screw Driver
Spirit Level
17mm ( 11 / 16 ”) Socket Wrench
or Shifter
The Telehook 30-50 Universal Rotating Wall Mount supports flat panel displays from 30” (76cm) to 50” (127cm)
and supports a maximum load of 85kgs (187lbs).
This product is factory set to support 35kgs (77lbs), and will need to be adjusted if the display is heavier or lighter.
The manufacturer does not accept responsibility for incorrect installation.
TIP: Use a spirit
level to ensure the
wall plate is
horizontal
C.1. Attaching the Display to the Wall Plate C.2. Pivot Head Load Capacity Adjustment
M4x16mm
Phillips Head
Screw (x6)
Centre Holes
Note: It is recommended to
mount the Wall Plate by firmly
fixing the four Coach Screws
into two studs. However, if the
weight of the display is less than
50kgs (110lbs), it is possible to
mount the Wall Plate to one stud
by fixing the two Coach Screws
through the two Centre holes.
Note: For demonstration purposes, the wall
has been omitted from the above image.