Atdec Telehook TH-WH-PJ-FM Installation manual - Manual

Component Checklist
Roll / Shift Adjustment
Component Checklist A
Check you have received all parts against the Component Checklist above.
Bits Bag
WARNING
WARNING: This bracket supports up to 15kg (33lbs).
DO NOT overload this bracket.
Ensure the Ceiling can support the total weight of the Projector and the Universal Flush Mount.
All bolts and screws must be used at the designated points in the installation instructions to prevent damage
to the projector, or personal injury.
DO NOT install near air conditioner vents or where there is excessive dust or smoke.
Ensure the projector is mounted so that it is not possible for excessive loads to be placed on the bracket.
Extension Brackets
150mm (x2) Extension Brackets
75mm (x2)
Square Nut (x8)
Cross Recessed Screws
M2.5x15 (x4)
M3x15 / M3x20 (x4 each)
M4x15 / M4x20 / M4x25 (x4 each)
M5x15 / M5x20 / M5x25 (x4 each)
M6x15 / M6x20 / M6x25 (x4 each)
M5x10mm
Socket Button
Cap Screw (x4)
Spacer
Large (x4)
Medium (x4)
Small (x4)
6mm Allen
Key (x1)
Bottom
Spacer (x4)
Flush Mount
Assembly (x1)
Nylon Anchor
Plug (x2)
Washer
20mm (x2)
10mm (x4)
8mm (x4)
14 Gauge Coach Screw (x2)
Allen Key
6mm
M8x50mm
Socket Cap
Screw
M8 Nyloc Nut
Ceiling Plate
Locking Hook
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 03.02.09©
F.1.
Connect the Shaft to the Ceiling Plate as shown
below.
Installation Instructions
Please read these
instructions before
commencing installation
as faulty installation could
result in injury. Atdec
assumes no responsibility
for faulty installations.
IMPORTANT
Removing the Ceiling Plate from the Flush Mount Assembly B
Attaching the Flush Mount Assembly to the Ceiling Plate F
Adjusting the Projector G
Installation Complete
F.3.
Tighten the Locking Hook with the M8x50mm
Socket Cap Screw and the M8 Nyloc Nut that
was previously removed.
F.2.
Insert the
Locking Hook
into the slot in
the Ceiling Plate
to lock the Flush
Mount Assembly.
Ceiling Plate
Locking
Hook
M8 Nyloc Nut
M8x50mm
Socket Cap
Screw Locking
Hook
6mm
Allen Key
Flush Mount
and Projector
M8x15mm
Screw
6mm
Allen Key
6mm
Allen Key
Remove the Ceiling Plate from
the Flush Mount Assembly as
shown.
Pitch Adjustment
Loosen
Tighten
3mm Allen
Key (x1)
To make Roll/Shift adjustments, first ensure the
weight of the projector is supported. Then loosen
the M8x65mm Screw with the supplied 6mm Allen
Key, and adjust to your desired position.
Re-tighten the screw firmly. To make Pitch adjustment, first ensure the weight
of the projector is supported. Then loosen both
M8x15mm Screws with the supplied 6mm Allen
Key, and adjust to your desired position.
Re-tighten both screws firmly.
6mm
Allen Key M8x65mm
Screw
Loosen
Tighten
SHIFT
Shaft
Extension
Brackets
100mm (x2)
Extension
Brackets
50mm (x2)
Tip: When the projector requires servicing, remove
the projector via this easy disconnection point to
save time.
Pitch Pitch Roll Roll
Projector Ceiling Mount |Flush
70