Atdec Telehook TH-3270-UFM Installation manual - Manual

TM
TIGHTEN
FIRMLY
Flat Screen Wall Mount | Full Motion
Installation Instructions
Component Checklist
Hardware
IMPORTANT INFORMATION
! IMPORTANT - Install Telehook Wall Mount as per Installation Instructions.
! Telehook Wall Mount has a universal mounting hole pattern that suits a broad range of TVs:
from150 to 805mm wide (6” to 31¾”) and 140mm to 500mm high (5½” to 19¾”).
! Maximum Load: 65kg (143lbs)
! The Manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
TH-3270-UFM
Step 2. Locate Drilling Position
WALL
Double-sided
tape (x2)
Drilling Guide
BACK
Un-fold the Drilling Guide and
open the Dust Collector. Peel away the backing from the
double-sided adhesive tape. Position the Drilling Guide vertically
onto the wall using a spirit level.
Choose the location of your Telehook Wall Mount, ensuring that the wall is structurally sound (for a timber stud
wall, locate the stud using a stud detection device). Use the Drilling Guide to mark out the hole centres.
Dust Collector
Drilling Guide
FRONT
Mounting Rail
Articulated Arm
Concrete
Anchor (x3)
5mm/6mm
Allen Key
M5 Washer
(x4)
M6 Washer
(x4)
M8x30mm / M8x50mm (x4 each)
M5x30mm / M5x45mm (x4 each)
M6x30mm / M6x45mm (x4 each)
M10 Coach
Screw (x3)
Mounting Screws
M4/5 Spacer
Bush (x4)
M6/8 Spacer
Bush (x4)
Drilling Guide
TOOLS REQUIRED:
• Power Drill
• Phillips Head Screwdriver
• Flat Blade Screwdriver
• Spirit Level
• 7mm (
9 /
32
”) Drill Bit
• 12mm (½”) Masonry Drill Bit
• 16mm (
5 /
8
”) Socket Wrench or Shifter
Step 8. Cable Management
Connect cables to your Display and
route through Cable Clips.
Step 9. Final Adjustment
As Display Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 14.03.12 ©
Remove Cable Covers using a Phillips Head Screwdriver, and route
the cables along the length of the arms. Reattach the Cable Covers
to hold the Cables in place.
TIP: Leave slack in the
cables to allow full
movement at the joints.
Loosen screw with 5mm Allen key
and tilt the Display as desired.
Tighten screw with 5mm allen key
to lock the Display in desired position.
Tilt Down
Tilt Up
Top
M10 Washer
(x3)
M8 Washer
(x4)
Mounting
Bracket (x2)
Installation Complete
Cable Covers
Cable Clip
Cables
TIP: The 5mm and 6mm
Allen Keys can be stored
in the Mounting Rail End
Caps.
End Cap
TIP: Use a Spirit Level to
check the Display is level.
Nylon
Washer
Mount Head
Screw
5mm Allen key
Step 7. Mounting the Display onto the Articulated Arm ( required)
Lower the Display so that the Hook
Plate locates with the Mounting
Head.
Mounting
Head
Hook
Plate
If necessary, adjust the horizontal
angle of the Mounting Rail so that
the Display is level. Fix the Display in position using the
Mount Head Screw and Nylon
Washer supplied (see hardware).
Mount
Head Screw
+/-5°
Adjustment
5mm
Allen Key
Nylon
Washer
TIGHTEN
LOOSEN