Trek 152P-2P Two Point Resistance Probe - Manual (Page 2)

CERTIFICATION
TREK, INC. certifies that each Model
152P-2P probe is tested and calibrated
to specifications using measurement
equipment traceable to the National
Institute of Standards and Technology or
traceable to consensus standards.
Probe Dimensions Distance Between Probe Contacts
(center to center)
6.4² length x 0.75² diameter
(163 mm x 19 mm).
0.25² (6.4 mm).
Cable Length Contact Travel
6 ft (1829 mm). 0.170 ² (4.3 mm).
Probe Contacts Contact Force
0.125² (3.2 mm) diameter 16 oz ( 454 g), nominal at
conductive silicon elastomer. 0.170² (4.3 mm) contact in-travel.
Performance Features
Battery Operation Test current Limit Resistance/Resistivity
Two (2) 9 Volt batteries (NEDA Limited to less than 13 mA in the Measurement Ranges
1604 Alkaline, or equivalent) 10 V range and less than 1.7 mA in
3 13 provide 6 hours of power for the 100 V range.
10 to 10 ohms
portable operation.
Probe Electrode Test Voltage
AC Line Operation User selectable for 10 V or 100 V,
Use the AC battery eliminator. The ±2%.
Measurement Accuracy (of reading)
eliminator output connector is a
female type 2.1 mm DC power plug.
At 25 °C ±10°C at 20% to 70% RH:
Instrument Dimensions
3 11
10 to 10 W range, ±5 %, 180 mm H x 100 mm W x
12 13 44 mm D
10 to 10 W range, ±10 %.
(7² H x 4² W x 1.75² D)
Instrument Weight
Approximately 0.5 kg (1 lb) with
ANSI/ESD Association Standards
batteries.
The Model 152 conforms to the
following ANSI/ESD Association
Environmental Operating Range
Standards for measuring surface
Temperature
resistance and surface resistivity:
15 °C to 35 °C.
Relative Humidity
5% to 80%, noncondensing.
14
(extends to 10 ohms using the
Concentric Ring probe).
LCD Display
Three digits plus two digit exponent
(scientific notation).
Low Battery Indicator
LCD message for low battery.
Test Voltage Range Indicator
User selectable, either 10 V or 100 V.
Automatic Shutoff
If the unit is left idle for longer than
10 minutes, the unit automatically
turns off.
STM2.1 Garments.
STM4.1 Work surfaces -
resistive characterization.
TREK, INC. certifies that each Model
STM7.1 Flooring materials.
152 Surface Resistance Meter is tested
STM9.1 Footwear resistive
and calibrated to specifications using
characteristics.
measurement equipment traceable to TREK, INC. 2.27 kg (5 lb.) Concentric
STM11.11 Surface resistance
the National Institute of Standards and Ring Probe, (2) 2.27 kg. (5 lb.) point-to- measurements of static
Technology or traceable to consensus point probes, and the two-point
dissipative planar
standards. resistance 152P-2P probe. materials.
STM12.1 Seating - resistive
measurements.
Please contact TREK, INC.
STM11.13 Two-point resistance
for information about
measurement.
additional EOS/ESD
STM97.1 Floor materials/footwear-
probes and instruments
resistance measurements
in combination with
active user.
General (cont.)
General
Certification
Probes Available
Model 10/40A Specifications
Model 152 P-2P Probe Specifications
Copyright ã 2011 TREK, INC. All specifications are subject to change. 1123/DEC
Model 152 Resistance Meter using the 152P-2P Probe
TREK, INC. • 190 Walnut Street • Lockport, NY 14094 • USA • 800-FOR TREK
(fax) • www.trekinc.com • [email protected] 716-438-7555 • 716-201-1804