Yamaha DG-1000 - Manual (Page 5)

3
GAIN
The Panel Controls
■ Front Panel
q
Input Jack (INPUT)
Connect the guitar to this jack.
* Switch the power OFF before connecting the guitar.
w
Trim Control (TRIM)
Matches the guitar output level to the pre-amp’s input level. (
→
pg. 4)
* TRIM level settings are not stored in memory.
e
Output Level Control (OUTPUT)
Controls the output level of the OUTPUT jack on the back panel. Matches
the output level to the amp’s input level. (
→
pg.4)
* Output level settings are not stored in memory.
r
Gain Volume (GAIN)
Controls the amount of distortion.
* No sound will be produced if GAIN is set to 0, even if the MASTER
volume
t is turned up.
t
Master Volume (MASTER)
Controls the overall volume of GAIN and tone controls settings.
y Tone Controls
(TREBLE, HIGH MID, LOW MID, BASS, PRESENCE)
Controls the levels of their respective frequencies.
u
MIDI Button
Press this button to edit settings in the MIDI mode. (
→
pg. 6)
i
Amp Select Button/Amp Select Display
(LEAD 1, 2/DRIVE 1,2/CRUNCH 1,2/CLEAN 1,2)
Selects one of the 8 preset amp types. The currently selected amp type
is shown on the display. (
→
pg. 4)
Also acts as the MIDI function switch when in the MIDI mode. (
→
pg. 6)
* When the amp select button is pressed, knobs r – y will return to their
preset positions (GAIN & MASTER = 7, Tone Controls all = 5).
o Mode Display Lamp (PLAY/EDIT/MIDI)
Displays the DG-1000’s currently selected mode.
• PLAY (Play Mode):
Automatically enters this mode when a memory number is recalled,
and when the power is switched on. (
→
pg. 4)
■ Rear Panel
q
w i e
r t y
u o !0 !1 !2 !4 !5 !6 !7
• EDIT (Edit mode)
Automatically enters this mode when tone control or amp select set-
tings are changed. (
→
pg. 4)
• MIDI (MIDI Mode)
MIDI functions are edited in this mode.
Press the MIDI button u to enter the MIDI mode. (
→
pg. 6)
!0
Display
Displays Memory Numbers, Program Change Numbers, MIDI Channel,
etc.
!1
/ Buttons
Increases or decreases the memory number by 1. Also, increases or
decreases values by 1, or switches the MIDI mode ON/OFF when in the
MIDI mode. Values change continuously when the button is pressed
and held.
!2
STORE Button (STORE)
Press this button to save current sound settings to internal memory.
( → pg. 5) Also, used to carry out bulk dump functions in the MIDI mode.
(
→
pg. 6)
!3
RECALL Button (RECALL)
Recalls settings from memory. Use the / buttons to select a
memory number (01 – 128), then press the RECALL button to recall
those settings from memory. ( → pg. 5)
!4
POWER Switch (POWER)
The power switch for the DG-1000.
* Set the OUTPUT Volume
e to 0 before turning the POWER ON/OFF.
!5
OUTPUT Jack (OUTPUT)
Connect to the power amp (or guitar amp). ( → pg. 4)
!6
MIDI IN Jack
Connected to a MIDI Foot Controller’s MIDI OUT jack, the DG-1000 can
be controlled by an external foot controller. (
→
pg. 6)
!7
MIDI OUT/THRU Jack
Connect to the MIDI IN jack of a device that can save MIDI data. Data
stored in the DG-1000’s memory can be saved to an external MIDI de-
vice (MIDI Data Filer, etc.). (
→
pg. 5)
Also, sends MIDI data, received by the MIDI IN jack !6 , to an external
device when MIDI Merge is set to ON. ( → pg. 6)
!3