Banks Power Dodge Trucks: (Diesel ’03 - 07 5.9L Cummins) Power Pack & Stinger Systems w_EconoMind '03-05 Compatible with Banks iQ - Manual (Page 30)

30
96820 v.4.0
Your EconoMind Diesel Tuner displays
the “4,3” diagnostic code (refer to
TROUBLESHOOTING in Section
10 on how to read codes) when it
needs to learn your transmission
configuration. This always occurs
when the EconoMind Diesel Tuner
is first installed on the truck. The
EconoMind Diesel Tuner is equipped
with advanced safety features to
preserve your automatic transmission.
One of them is the capability to detect
the occurrence of transmission slip,
and it will automatically de-rate the
engine output power accordingly.
Before this safety feature can take
effect, the EconoMind Diesel Tuner
needs to learn that your truck
is equipped with an automatic
transmission.
1.
The following driving test shall
be performed in an area where
speeds over 55mph are safe and
traffic is light. For a vehicle with a
manual transmission, follow Step
2. For a vehicle with an automatic
transmission, follow Step 3. While
driving, listen for any exhaust leaks or
rattles, or intake boost leaks. After the
engine cools, re-tighten clamps and
hoses if leaks are detected.
2.
(Manual trans) To teach the
EconoMind Diesel Tuner that your
truck is equipped with a manual
transmission, drive the truck at a
speed over 55 mph for at least 2
minutes. The “4,3” diagnostic code
will be eliminated.
Repeat if necessary to eliminate code.
Proceed to Section 10.
3.
(Auto Trans) To teach the
EconoMind Diesel Tuner that your
truck is equipped with an automatic
transmission drive the truck at a
speed over 55mph until the torque
converter is locked (the toque
converter is usually locked at speeds
over 55mph). With the torque
converter locked and with turbo boost
below 10psig (ie, light load), maintain
the attained speed steadily for at least
30 seconds. Once the transmission is
learned, the “4,3” diagnostic code will
be eliminated. Repeat if necessary to
eliminate code.
-END, SECTION 9-
Section 9
TRANSMISSIoN LEARNNG
EconoMind Troubleshooting using
The Banks iQ
Check the Banks iQ’s Status indicator
for the “OK” icon on the upper left
corner of the iQ screen. Any Tuner
fault will be indicated by the “Banks
Engine” icon (see Figure 39) and
its cause can be investigated by
running a ‘Tuner Diagnostic’ from the
Diagnostic menu.
1.
In the Environment select menu
press on the ‘Diagnostics’ button.
See Figure 40.
2.
In the Diagnostics menu press on
the ‘Tuner Diagnostics’ button to run
a tuner diagnostics. See Figure 41.
3.
The ‘Self Diagnostic’ screen
displays a log of diagnostic events
related to the Power Tuner. The
‘Logged Events’ list takes a moment
to update each time this screen is
opened. Once the list is updated,
the most current event will appear
at the bottom of the list. Each event
has an associated timestamp and
description, which will be displayed
below the list when that event is
highlighted. Each key cycle of the
vehicle produces a minimum of two
logged events. See Figure 42. Table
1 lists the common diagnostic codes
and the suggested course of action
for each.
4.
Use the arrow buttons to scroll
through the recorded events.
5.
Touch the Banks iQ icon on the
lower left of the screen to return to
the environment screen or the return
icon to return to the Diagnostics
menu.
6.
A pop-up “Log-File” screen will
appear asking you if you want to
erase the contents of the log. Press
‘No’ to keep the contents on Log-file
or ‘Yes’, to erase the Log-files.
Section 10
TRouBLESHooTING, ECoNoMIND
Figure 39
Banks Engine
Icon
Figure 40