RAM Mount RAM-234-HUB1U - Manual

RAM TOUGH-HUB INSTRUCTIONS
RAM TOUGH-HUB INSTRUCTIONS
Parts Index
A . RAM TOUGH-HUB (QTY. 1)
B. BARE WIRE POWER CABLE (QTY. 1)
C. IGNITION TRIGGER WIRE (QTY. 1)
D. USB CABLE (QTY. 1)
E. USB PORT FRAME (QTY. 1)
G. 1/4” SCREW FOR USB FRAME (QTY. 2, + 2 EXTRA)
F. FOAM STRIP FOR USB FRAME (QTY. 1)
-5 QTY. USB PORTS -ADDITIONAL USB PORT
-RJ 45 ETHERNET PORT
-12-48 VOLT DC INPUT -IGNITION TRIGGER
-USB OUTPUT PORT
1. USE (F) FOAM STRIP TO ADHERE UNDER (E) USB
PORT FRAME.
2. POSITION (E) USB PORT FRAME IN FRONT
OF THE 5 USB PORTS.
3. SECURE TO HUB USING (G) SCREWS.
ONLY RECOMMENDED FOR USB PORTS THAT DO NOT
FREQUENTLY CONNECT AND DISCONNECT
- CONSTANT ON, IGNITION TRIGGER HAS NO EFFECT
- TIME DELAY FOR 5 MINUTES
- TIME DELAY FOR 15 MINUTES
- TIME DELAY FOR 45 MINUTES POS 0
POS 1
POS 2
POS 3
IGNITION TRIGGER CAN BE WIRED TO THE IGNITION
OF THE VEHICLE (OR OTHER 12V IGNITION SOURCE)
TO PROVIDE A TIMED DISCONNECT TO THE
CONNECTED PERIPHERALS AFTER VEHICLE HAS
BEEN TURNED OFF. WHEN VEHICLE IGNITION IS OFF,
TOUGH-HUB CONTINUES TO PROVIDE POWER TO THE
CONNECTED PERIPHERALS FOR A PRE SET
DURATION OF TIME. THE DEFAULT DELAY IS PRE SET
FROM THE FACTORY TO 15 MINUTES.
TO CHANGE DEFAULT PRE SET, REMOVE HOUSING AND
SWITCH THE SMALL JUMPER COMPONENT FROM “POS 2”
TO ANY OF THE OTHER 3 POSITIONS:
COMPLETE ASSEMBLY
A
B
C
D
E
F
G
Parts Index
A . RAM TOUGH-HUB (QTY. 1)
B. BARE WIRE POWER CABLE (QTY. 1)
C. IGNITION TRIGGER WIRE (QTY. 1)
D. USB CABLE (QTY. 1)
E. USB PORT FRAME (QTY. 1)
G. 1/4” SCREW FOR USB FRAME (QTY. 2, + 2 EXTRA)
F. FOAM STRIP FOR USB FRAME (QTY. 1)
-5 QTY. USB PORTS -ADDITIONAL USB PORT
-RJ 45 ETHERNET PORT
-12-48 VOLT DC INPUT -IGNITION TRIGGER
-USB OUTPUT PORT
1. USE (F) FOAM STRIP TO ADHERE UNDER (E) USB
PORT FRAME.
2. POSITION (E) USB PORT FRAME IN FRONT
OF THE 5 USB PORTS.
3. SECURE TO HUB USING (G) SCREWS.
ONLY RECOMMENDED FOR USB PORTS THAT DO NOT
FREQUENTLY CONNECT AND DISCONNECT
-
- TIME DELAY FOR 5 MINUTES
- TIME DELAY FOR 15 MINUTES
- TIME DELAY FOR 45 MINUTES CONSTANT ON POS 0
POS 1
POS 2
POS 3
IGNITION TRIGGER CAN BE WIRED TO THE IGNITION
OF THE VEHICLE (OR OTHER 12V IGNITION SOURCE)
TO PROVIDE A TIMED DISCONNECT TO THE
CONNECTED PERIPHERALS AFTER VEHICLE HAS
BEEN TURNED OFF. WHEN VEHICLE IGNITION IS OFF,
TOUGH-HUB CONTINUES TO PROVIDE POWER TO THE
CONNECTED PERIPHERALS FOR A PRE SET
DURATION OF TIME. THE DEFAULT DELAY IS PRE SET
FROM THE FACTORY TO 15 MINUTES.
TO CHANGE DEFAULT PRE SET, REMOVE HOUSING AND
SWITCH THE SMALL JUMPER COMPONENT FROM “POS 2”
TO ANY OF THE OTHER 3 POSITIONS:
COMPLETE ASSEMBLY
A
B C
D
E
F
G
BLUE LED LIGHT BLINKS DURING TIME DELAY
BLUE LED LIGHT BLINKS DURING TIME DELAY
RMR-INS-234-HUB1
RMR-INS-234-HUB1