RAM Mount Uni-Conn™ Assembly Guide for RAM Tab-Lock™ & Tab-Tite™ Series - Manual

E
A
CHANGING LOCK COMBINATION:
UNLOCK MODE:
RAM UNI-CONN™ ASSEMBLY GUIDE FOR APPLE IPAD
WARNING: BACKUP CODE NOT AVAILABLE IF
COMBINATION IS FORGOTTEN OR LOST.
FACTORY PRESET: “1 1 1 1”
TO UNLOCK, ALIGN PRESET OR CURRENT COMBINATION (A) AND
PULL PLUNGER OUTWARD (B) UNTIL INDENTATION IS VISIBLE
NEXT TO ARROW (C).
2. ON REVERSE SIDE, LOCATE SQUARE NOTCH ON OF SLOT
TO THE LEFT OF COMBINATION NUMBERS (D). SPIN SLOT
DOWNWARD, BRINGING SQUARE NOTCH TO BOTTOM OF
SLOT (E). PEN OR SCREWDRIVER RECOMMENDED.
3. SET NEW COMBINATION ON THE FRONT SIDE OF LOCK IN
LINE WITH ARROW.
4. MOVE SLOT BACK UPWARD TO ORIGINAL POSITION UNTIL
IT STOPS (F). NEW COMBINATION WILL BE SET.
1. SET LOCK TO UNLOCK MODE (SEE ABOVE), WITH
PLUNGER PULLED OUTWARD.
PLUNGER OUT: LATCH WILL BE LOOSE
PLUNGER IN: LATCH WILL BE LOCKED IN POSITION
National Products, Inc., 8410 Dallas Ave S., Seattle, WA 98108, (206) 763-8361 www.ram-mount.com
RMR-INS-TABD7
PARTS INDEX
A.) 1-QTY. BOTTOM IPAD DOCKING CUP
B.) 1-QTY. STEEL CLAMP PLATE
C.) 2-QTY. #4-40 X 1.25” FLAT HEAD MACHINE SCREWS
D.) 1-QTY. BOTTOM DOCK COVER
E.) 2-QTY. CABLE TIES (1 SPARE) A
B
C D
E
FOR SQUEEZE-TYPE DOCKING
CONNECTORS, USE SPARE (E)
CABLE TIE TO PERMANENTLY
PRESS SIDES TOGETHER.
1. (OPTIONAL) INSERT (E) CABLE TIE THROUGH
SLOT ON BACK OF (A)DOCK FOR WIRE RETENTION. 2. INSERT CONNECTOR THROUGH BOTTOM OF (A) DOCK. FRONT
SIDE OF CONNECTOR MUST FACE APPROPRIATE DIRECTION.
4. INSERT USB SIDE OF CABLE THROUGH (B) CLAMP
PLATE. INSERT CLAMP PLATE INTO (A) DOCK. 5. ATTACH (C) SCREWS TO HOLES ADJACENT TO PINS
USING PHILLIPS HEAD SCREWDRIVER UNTIL SNUG.
DO NOT OVER-TIGHTEN 6. ATTACH (D) BOTTOM COVER TO (A) DOCK,
SLOTTED SIDE FACING BACK.
7. (OPTIONAL) TIGHTEN (E) CABLE TIE AROUND
POWER CABLE TO PROVIDE CABLE RETENTION.
3. CAREFULLY PRESS CONNECTOR SO PINS
FULLY PROTRUDE FROM CENTER SLOT.
B
C
D
E
RAM UNI-CONN™ ASSEMBLY GUIDE FOR RAM TAB-LOCK™ & TAB-TITE™ SERIES
E
A
National Products, Inc., 8410 Dallas Ave S., Seattle, WA 98108, (206) 763-8361 www.ram-mount.com
RMR-INS-TABD7
PARTS INDEX
A.) 1-QTY. BOTTOM IPAD DOCKING CUP
B.) 1-QTY. STEEL CLAMP PLATE
C.) 2-QTY. #4-40 X 1.25” FLAT HEAD MACHINE SCREWS
D.) 1-QTY. BOTTOM DOCK COVER
E.) 2-QTY. CABLE TIES (1 SPARE) A
B
C D
E
FOR SQUEEZE-TYPE DOCKING
CONNECTORS, USE SPARE (E)
CABLE TIE TO PERMANENTLY
PRESS SIDES TOGETHER.
1. (OPTIONAL) INSERT (E) CABLE TIE THROUGH
SLOT ON BACK OF (A)DOCK FOR WIRE RETENTION. 2. INSERT CONNECTOR THROUGH BOTTOM OF (A) DOCK. FRONT
SIDE OF CONNECTOR MUST FACE APPROPRIATE DIRECTION.
4. INSERT USB SIDE OF CABLE THROUGH (B) CLAMP
PLATE. INSERT CLAMP PLATE INTO (A) DOCK. 5. ATTACH (C) SCREWS TO HOLES ADJACENT TO PINS
USING PHILLIPS HEAD SCREWDRIVER UNTIL SNUG.
DO NOT OVER-TIGHTEN 6. ATTACH (D) BOTTOM COVER TO (A) DOCK,
SLOTTED SIDE FACING BACK.
7. (OPTIONAL) TIGHTEN (E) CABLE TIE AROUND
POWER CABLE TO PROVIDE CABLE RETENTION.
3. CAREFULLY PRESS CONNECTOR SO PINS
FULLY PROTRUDE FROM CENTER SLOT.
B
C
D
E
RAM UNI-CONN™ ASSEMBLY GUIDE FOR RAM TAB-LOCK™ & TAB-TITE™ SERIES