RAM Mount RAM-VB-129-SW1 - Manual

This document, including images, may not be reproduced partly or fully without the expressed written consent of National Products, Inc.
SPECIFICATIONS
Placement
Passenger side on horizontal section of seat
rail. For Sprinter, between seat cushion and
seat frame box passenger side front of seat
Drilling Required
No - uses existing seat bolts
Seat Configuration
Bucket
Construction/Finish
Steel/Black Powdercoat
Dimensions
A = 19.375” B = 7.125”
Hole Center = 16.5"
Pole or Pedestal
Purchased Separatel
Weight = 4.9 lbs.
Features
RAM-VB-129-SW1
RAM-VB-129
Important Note
Installs with no drilling required
Minimal intrusion into passenger leg space
In 2005 and 2011 model year vehicles, the seat leg bolts may be tied to the air
bag system. Tampering with these may result in disabling the air bag
system and causing a severe safety hazard. The installation of this
product into these vehicles should only be done by a Dodge factory
authorized technician or Up-fitter familiar with Police, Fire, and Rescue
vehicles and their fleet use.
RAM No-Drill
TM
Seat Bases
National Products, Inc.
Item Number
RAM-VB-129 & RAM-VB-129-SW1
National Products, Inc.
Website: www.ram-mount.com
Email: [email protected]
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
National Products, Inc.
Website: www.ram-mount.com
Email: [email protected]
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
COMPATIBLE VEHICLES:
DODGE CHARGER (2005, 2011-2013)
DODGE CHARGER POLICE (2005, 2011-2013)
DODGE MAGNUM (2005)
DODGE MAGNUM POLICE (2005) DODGE CHALLENGER (2011)
DODGE SPRINTER VAN (2007-2010)
FREIGHTLINER SPRINTER VAN (2010-2011)
MERCEDES SPRINTER VAN (2010-2013)
INSTALLATION INSTRUCTIONS
This document, including images, may not be reproduced partly or fully without the expressed written consent of National Products, Inc.
RAM No-Drill
TM
Seat Bases
National Products, Inc.
Item Number
RAM-VB-129 & RAM-VB-129-SW1
For the Dodge Charger you will need an E12 socket. If you are using a RAM Tele-Pole system, attach the lower female
tube prior to installing the no drill base in the vehicle. It is suggested to install the mounting hardware so the rubber nut
caps are on the top side.
1. Loosen the seat leg bolts on the passenger side that hold the seat to the floor pan. These are located at the front
center of the seat tracks. It is not necessary to remove these. Only loosen them enough to clear the no drill base.
2. Once the bolts are loose, gently lift the front of the seat to create enough space for the base to fit between the seat
frame legs and floor board.
3. Align the slots with the seat leg bolts and slide the base completely under the legs until the back of the slots contacts
the seat leg bolts.
4. Fully tighten the seat leg bolts to secure the no drill base in place.
For installation into Vans, the slots are not used but the holes instead.
1. Remove the two seat bolts holding the seat tracks to the seat frame box.
2. Place the base between the seat tracks and seat frame box and align the holes. Replace the seat bolts and fully
tighten.
COMPATIBLE VEHICLES:
DODGE CHARGER (2005, 2011-2013)
DODGE CHARGER POLICE (2005, 2011-2013)
DODGE MAGNUM (2005)
DODGE MAGNUM POLICE (2005) DODGE CHALLENGER (2011)
DODGE SPRINTER VAN (2007-2010)
FREIGHTLINER SPRINTER VAN (2010-2011)
MERCEDES SPRINTER VAN (2010-2013)